3. A 300MHz, 5002 source needs to be connected to two properly matched 500 transmission lines (Z02) in parallel. Use a quarter wavelength transformer (Z01) to compensate for the mismatch. What is Zo1 of the quarter wavelength section and how long will this section be if the relative velocity in the transmission lines is 50% than that of the speed of light. Zs = 50Ω Zo1 Zo2 = 500 Zo2 = 500 Z₁ = 500 Z, = 50Ω

3. A 300MHz, 5002 source needs to be connected to two properly matched 500 transmission lines (Z02) in parallel. Use a quarter wavelength transformer (Z01) to compensate for the mismatch. What is Zo1 of the quarter wavelength section and how long will this section be if the relative velocity in the transmission lines is 50% than that of the speed of light. Zs = 50Ω Zo1 Zo2 = 500 Zo2 = 500 Z₁ = 500 Z, = 50Ω

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(i) Which mode of propagation is used by shortwave broadcast services having frequency range from a few MHz upto 30 MHz? Explain diagrammatically how long distance communication can be achieved by this mode. (ii) Why is there an upper limit to frequency of waves used in this mode?
State the difference between high and low frequency signals travel in typical transmission lines.
Solve for Icsat when B = 40, Vce,sat = 0.2V and Vcc = 12V. Do not suppose that Ib is negligible.
Question)The coupling factor and isolation of a lossless, symmetric directional coupler are 8 dB and 20 dB respectively. Determine the scattering matrix of the directional coupler. Also determine the directivity of the device? This Question from Microwave systems course.
Q. A base stationcellular communicationsystems lossless antenna has a maximum gain of 16 dB (above isotropic) at 1,900 MHz. Assuming the input power to the antenna is 8 watts, what is the maximum radiated power density (in watts/cm2 ) at a distance of 100 meters? This will determine the safe level for human exposure to electromagnetic radiation.
The radio path (f = 900 MHz) between a mobile phone and the base station has a loss of 30 dB in addition to the free space loss. The base station measures the level of the signal transmitted by the phone, and it sends the phone a command to set the transmit power to a level, which gives a received power level of-90 dBm. The antenna gain of the phone is 2 dB and the receive gain of the base station antenna is 7 dB. The distance between the phone and the base station is 500 m. What will be the transmit power level of the phone?
please do it correctly.. A system starts with omnidirectional transmit antennas. This produces a coverage area with a radius of 1500 m when there is a pathloss exponent of 3.8. If directional antennas are implemented with a gain of 7.070 dB, what does the radius become (in meters)?
What should be the relative dielectric constant of the dielectric material between the plates so that the propagation speed is 1x10^8 m/s in a 50 ohm parallel plate transmission line to be used at 3 GHz?
Determine the radio horizon for a transmit antenna that is 100 ft high and a receiving antenna that is 50 ft high and for antennas at 100 m and 50 m.
a) A parallel plate transmission line has plate separation d=1 cm, and isfilled with teflon having dielectric constant ε’r=2. Determine themaximum operating frequency such that only TEM mode willpropagate. Also find the range of frequencies over which TE1 andTM1 modes will propagate and no higher order modes. b) In the parallel plate waveguide of part -a, the operating wavelength isλ=2mm. How many waveguide modes will propagate?
A simple point-to-point microwave transmission link has no redundancy. Failure of the link will result in an outage. Therefore, typical microwave transmission links are designed with redundancy. Explain the following redundancy techniques 1+1 Hot Standby (HSB), 1+1 Space Diversity (SD), and 1+1 FD (Frequency Diversity).please explain.
Calculate the guided intrinsic impedance at 20 GHz for the lowest-order mode of therectangular waveguide with dimensions a=0.7 in and b=0.3 in.Take relative permittivity as 2.76.