show complete diagram fbd and solution 3.) A concrete square column 250 mm x 250 mm is to be reinforced by deformed steel bars to carry a loadof 500 kN. the properties of concrete and steel are as follows:Deformed Steel barsConcrete1206Allowable Stress (Mpa)Modulus of Elasticity (Gpa)20014Determine the number of deformed steel bars and show a detail of the cross-section of your design.Commercially available deformed bars are 12 mm, 16 mm, 20 mm, 25 mm, 32 mm, and 36 mm indiameter.

Given, 250 mm x 250 mm section Pu = 500 kN

3.) A concrete square column 250 mm x 250 mm is to be reinforced by deformed steel bars to carry a load of 500 kN. the properties of concrete and steel are as follows: Deformed Steel bars Concrete 6 120 Allowable Stress (Mpa) Modulus of Elasticity (Gpa) 200 14 Determine the number of deformed steel bars and show a detail of the cross-section of your design. Commercially available deformed bars are 12 mm, 16 mm, 20 mm, 25 mm, 32 mm, and 36 mm in diameter.

3.) A concrete square column 250 mm x 250 mm is to be reinforced by deformed steel bars to carry a load of 500 kN. the properties of concrete and steel are as follows: Deformed Steel bars Concrete 6 120 Allowable Stress (Mpa) Modulus of Elasticity (Gpa) 200 14 Determine the number of deformed steel bars and show a detail of the cross-section of your design. Commercially available deformed bars are 12 mm, 16 mm, 20 mm, 25 mm, 32 mm, and 36 mm in diameter.

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter5: Measuring Concrete Work

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Similar questions

Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. 1. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = (5 decimal places) 2. if the tensile strain is set as 0.010 upon crushing of concrete at a strain of 0.003. = (5 decimal places) 3. Minimum as required by NSCP 2015. = (5 decimal places)
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
Calculate the tensile steel stress of 5-16-mm-dia rebars in a concrete beam 240 mm by 450 mm at ultimate stage if f'c = 21 MPa and fy = 420 MPa. Express your answer in whole number.
The properties of the reinforced concrete beam are b = 300 mm, d = 480 mm, Ast = 1306 mm2, and Est / Eco = 10. If the working stresses are 16.7 MPa for concrete and 104.8 MPa for steel, determine the corresponding bending moment (in Nm) for the concrete. Round off the final answer to two decimal places.
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. 16. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = [r] (5 decimal places)
A rectangular concrete beam 277 mm wide and 495 mm deep is simply supported over a span of 8.37 m. the beam is reinforced with straight tendons situated 59 mm above the bottom of the beam under a prestressing force of 387 kN. Concrete weighs 23.36 kN/m3 with modulus of elasticity Ec=13,814.76 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads. (Include the sign if it is negative) Please avoid rounding off values during the course of solution proper as much as possible. Always write your answer in 4 decimal places
Calculate the tensile steel strain of 5-16-mm-dia rebars in a concrete beam 240 mm by 410 mm at ultimate stage if f'c = 20 MPa and fy=420 MPa. Express your answer in 5 decimal places
From National Structural Code of the Philippines 2015, what is the: 1. Minimum/maximum value of steel strain(εt) 2. Minimum/maximum value of steel stress (fs) 3. Maximum/minimum values of concrete stress (fc’)
A BEAM SECTION IS SHOWN IN THE FIGURE BELOW IS A SIMPLY SUPPORTED OVER A SPAN OF 8M. THE BEAM IS REINFORCED WITH STRAIGHT TENDONS. ASSUMING TENSION CONCRETE DOES NOT CRACK, WHAT IS THE DEFLECTION AT MIDSPAN (NET DEFLECTION) DUE TO GIVEN LOADS WITH BEAM SECTION PROPERTIES LISTED BELLOW. (Note: include the sign if negative) (mm) BEAM PROPERTIES: F'C = 28 MPA PRESTRESSING FORCE = 350 KN UNIT WEIGHT OF CONCRETE = 23.6 KN/CU.M Please avoid rounding off values during the course of solution proper as much as possible. Always write your answer in 3 decimal places
Civil Engineering You perform three replicate tests on typical 6x12” concrete cylinders at 28 days and get the data below. Compute the average compressive strength and the average split tensile strength. Report your results to the precision given by ASTM Compression test, peak load (lbs) 127,260 129,300 128,710 Split tension test, peak load (lbs) 52,810 53,640 55,010
Calculate the tensile steel strain of 5-16mm-diameter rebars in a concrete beam 240 mm by 420mm at ultimate stage if f'c = 26Mpa and fy = 420 MPa
please answer these two question 1.Explain the reason that flexural modulus of elasticity and compression test modulus of elasticity must be considered separately when both the flexural test and the parallel to grain compressive test caused normal stresses parallel to the grain of the wood. 2. Discuss the difference between isotropic and orthotropic materials for wood.