3. A layered soil is shown with the corresponding values K1, K2, and K3. a. Compute the equivalent horizontal coefficient of permeability b. Compute the equivalent vertical coefficient of permeability c. Compute the ratio of the equivalent horizontal coefficient of permeability to the equivalent vertical coefficient of permeability H1= 3 m K1 =2 x 10 cm/s H2= 4 m K1 =3.2 x 10?cm/s H= 12 m H3= 5 m K1 =4.1 x 10 cm/s

3. A layered soil is shown with the corresponding values K1, K2, and K3. a. Compute the equivalent horizontal coefficient of permeability b. Compute the equivalent vertical coefficient of permeability c. Compute the ratio of the equivalent horizontal coefficient of permeability to the equivalent vertical coefficient of permeability H1= 3 m K1 =2 x 10 cm/s H2= 4 m K1 =3.2 x 10?cm/s H= 12 m H3= 5 m K1 =4.1 x 10 cm/s

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter9: Consolidation

Section: Chapter Questions

Problem 9.20CTP

See similar textbooks

Similar questions

A layered soil has the following details: H₁ = 3ft, k₁ = 10-4 cm/sec : H ₂ = 4ft, k₂ = 3.2x10ˉ² cm/sec: H₃ = 6 ft, k₃ = 4.1x10ˉ⁵ cm/sec. What is the equivalent vertical permeability? a. 5.14 x 10ˉ⁵ b. 7.37 x 10ˉ⁵ c. 6.23 x 10ˉ⁵ d. 9.81 x 10ˉ⁵
A three-layer soil has the following properties: Layer 1: k = 2.77 x 10^-3 cm/s, H = 3.17 m. Layer 2: k = 1.6 x 10^-2 cm/s, H = 4.97 m. Layer 3: k = 3.06 x 10^-3 cm/s, H = 4.25 m. Determine the equivalent vertical coefficient of permeability of the soil arrangement. Layer 1 is on top of layer 2 while layer 2 is on top of layer 3. Round off to four decimal places.
A layered soil is shown in the figure below. Given that H1 = 1 m, k1 = 10-4 cm/sec H2 = 1 m, k2 = 2.8 x 10-2 cm/sec H3 = 2 m, k3 = 3.5 x 10-5 cm/sec Estimate the ratio of equivalent permeability, kH(eq)/kV(eq).
A three-layer soil has the following properties: Layer 1: k = 2.81 x 10^-3 cm/s, H = 3.95 m. Layer 2: k = 1.94 x 10^-2 cm/s, H = 4.51 m. Layer 3: k = 3.36 x 10^-3 cm/s, H = 4.15 m. Determine the equivalent vertical coefficient of the permeability of the soild arrangement. Layer 1 is on top of layer 2 while layer 2 is on top of layer 3.
A layer soil has the following data: H1=3m K1=2x10^-2 cm/sH2=4m K2=3.2x10^-2 cm/sH3=6m K3=4.1x10^-2 cm/s a) Compute the equivalent coefficient of permeability in the vertical directionb) Compute the velocity of flow if h =4 m.
Determine the average vertical permeability in mm/s of a soil mass made up of three horizontal strata, each 1 m thick, if the coefficients of permeability are 1 × 10^–1 mm/s, 3 × 10^-1 mm/s, and 8 × 10^–2 mm/s for the three layers.
Question 34 A three-layer soil has the following properties: Layer 1: k = 2.72 x 10^-3 cm/s, H = 3.02 m. Layer 2: k = 1.7 x 10^-2 cm/s, H = 4.93 m. Layer 3: k = 3.16 x 10^-3 cm/s, H = 4.04 m. Determine the equivalent vertical coefficient of permeability of the soil arrangement. Layer 1 is on top of layer 2 while layer 2 is on top of layer 3. Round off to four decimal places.
For a normally consolidated insensitive clay 0_CD= 30°. Deviator stress at failure of the same soil is 250 kN/m2 in CU test. If Skempton's A-parameter at failure is 0.62, find out the confining pressure during the consolidation state. a 280 b. 260 c. 270 d. 250
For a given consolidated clay: Gs= 2.71; LL= 45; In situ average effective overburden pressure = 120 kPa; In situ void ratio= 0.80 ; Thickness of clay layer = 4m ; average increase of effective stress on clay layer= 40 kPa; Effective pressure at the mid-height of clay layer= 60 kPa; Swell Index (Cs)= 1/5 Cc. Compute the pre-consolidation pressure in kPa. Show free body diagram a.92.9 b.100.5 c.49 d.87.64
Determine the average horizontal and vertical permeabilities of a soil mass made up of three horizontal strata, each 1 m thick, if the coefficients of permeability are 1 × 10–1 mm/s, 3 × 10–1 mm/s, and 8 × 10–2 mm/s for the three layers.
A layered soil is shown with the corresponding values K1, K2, and K3. Compute the equivalent horizontal coefficient of permeability Compute the equivalent vertical coefficient of permeability Compute the ratio of the equivalent horizontal coefficient of permeability to the equivalent vertical coefficient of permeability
A dense silt has the following properties: Void ratio (e) = 0.40, SpecificGravity (Gs) = 2.70, Effective diameter d10 = 1x10^-6 m, Capillary constant (C) = 0.20 cm^2. Free ground water level is 8.0 m below the ground surface. a. Find the height of capillary rise in the silt. b. Find the vertical effective stress in kPa at 5m depth. Assume that the soil abovethe capillary zone or capillary action rise to be dry soil and the soil within thecapillary action be partially saturated (degree of saturation, S) at 50%. c. Find the vertical effective stress at 10m depth. Assume that the soil above thecapillary zone or capillary action rise to be dry soil and the soil within the capillaryaction be partially saturated (degree of saturation, S) at 50%.