3. A pipe shown in the figure is discharging oil with spgr = 0.84 from a reservoir. If the head loss from point 1 to point 2 is 1.25 m and from point 2 to point 3 is 2.5 m, determine the following. a. Energy head at point 2 with reference from the datum b. Discharge at point 3 c. Pressure at point 2 3 m 50-mm-diameter 6 m

3. A pipe shown in the figure is discharging oil with spgr = 0.84 from a reservoir. If the head loss from point 1 to point 2 is 1.25 m and from point 2 to point 3 is 2.5 m, determine the following. a. Energy head at point 2 with reference from the datum b. Discharge at point 3 c. Pressure at point 2 3 m 50-mm-diameter 6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in series between two reservoirs with a difference in level of 12 m. The friction factors are 0.024, 0.021 and 0.019 respectively. The lengths are 200 m, 300 m and 250 m respectively. a) The flow in m^3/s in PIPE 3 is nearest to... b) What is the head loss in meters in pipe 3? c) Determine the length of an equivalent 350mm diameter pipe.
3 .Consider the incompressible flow of an ideal fluid having a density ρ = 1600 kg / m3 (figure 3). We give: P1 = 2 105Pa, P2 = 3 105Pa, V2 = 1 m / s and V1 = 0.5m / s. Determine the net power of the pump to ensure a volume flow Qv = 0.01 m3 / s.
determine the flow that comes out into the atmosphere in F, tabulate and plot the hydraulic gradient line of the system shown. Ya= 11m diameter 2= 18 cm L2= 85 m
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference ?????? ?????−???? ?????= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
Two reservoirs A and B having elevations 250 m and 150 m, respectively are connected by a 250mm diameter pipe 500 m long. A turbine is installed between the two reservoirs. The flow of water in the pipe is 140 L/s. Use Hazen Williams formula with /(C_1=120/). a. What is the head loss in pipe due to friction? b. What is the head extracted by the turbine. c. What is the power extracted by the turbine in kW.
Figure P8.19 shows a pipeline through which water flows at a rate of 0.06 m3/s. The pipe is 3000 m long, it has a diameter of 120 mm, and it is straight. If the friction factor for the pipe is 0.03 and the loss coefficient for the pipe entrance is 1.0, calculate H, the depth of the reservoir, given that the pipe exits to atmosphere.
A series of three parallel pipes connect the bottom of two reservoirs. All pipes are made of the same material with a ks value of 0.052. The pipe lengths are 70, 65 and 100 meters and the diameters are 0.4, 0.35 and 0.5 m, respectively. The change in head between the two reservoirs is 20 meters. Determine the velocity in each pipe.
An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter discharge pipe. Respectively each pressure reads 1.12 bars and 0.96 bars. The water flow measured 12.500 liters/min.at normal temperature. Calculate the following: 1. Head at the discharge side, m 2. Velocity Head. m 3. Total Head of the pump, m
2. A 6 in. pipe, as shown in the figure, takes water from a reservoir and terminates in a nozzle having a jet diameter of 2 in. Assuming a nozzle loss of 8 percent of the velocity head in the jet, compute the discharge (in SI units). Also, make a table showing the elevation head, velocity head, pressure head, and total head at each of the six stations. Lastly, draw the hydraulic gradient line (H.G.L.) & the energy gradient line (E.G.L.). Head losses in pipe: 1 to 2: 3.00 m 2 to 3: 9.00 m 3 to 4: 4 to 5: 18.00 m 6.00 m 1 W.S. ELEV. 140 ELEV. 128 M ELEV. 15M 5 6
Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in series between two reservoirs with a difference in level of 12 m. The friction factors are 0.024, 0.021 and 0.019 respectively. The lengths are 200 m, 300m and 250 m respectively. a.) Find the flow in m^3/s in PIPE 3. b.) What is the head loss in meters in pipe 3? c.) Determine the length of an equivalent 350 mm diameter pipe.
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference Pfresh water- Psea water= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
In Figure 6 is shown a siphon discharging water from reservoir A into the air at B. Distance 'a' is 1.8 m, 'b' is 6 m, and the diameter is 150 mm throughout. If there is a Total Head Loss is 1.5 m between A and the summit, and 1.5 m between the summit and B, Determine the rate of discharge in cubic meter per second.