3. A steel bolt through a 31-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch. a. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places.) b. Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.) c. Find the stress (in psi) induced in the steel bolt by the temperature change. d. Find the stress (in psi) induced in the aluminum tube by the temperature change.

3. A steel bolt through a 31-in long aluminum tube has the nut turned on until it just touches the end of the tube. No stress is introduced on the bolt or the tube. The temperature of the assembly is raised from 70 to 81 degrees Fahrenheit. The cross-sectional area of the bolt is 0.09 sq. inch and the cross-sectional area of the tube of 0.30 sq. inch. a. Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places.) b. Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.) c. Find the stress (in psi) induced in the steel bolt by the temperature change. d. Find the stress (in psi) induced in the aluminum tube by the temperature change.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
The standard length of a tape is 100m having a weight of 1.2kg with the standard temperature of 20 ̊C and standard pull of 5.5kg. The young modulus of elasticity of the tape is 200GPa, cross sectional area is 2.8mm2 and the coefficient of linear expansion is 0.0000116/ ̊C. Determine the normal tension of the tape. Hint: The normal tension of a tape is the applied tension which will cause the effects of pull and sag to neutralize each other.
A 13 in length of aluminum tubing (with E = 11.4 x 106 psi and  = 12 x 10-6 /deg F) having a cross-sectional area of 1.6 in2 is installed with “fixed” ends so that it is stress-free at 70 deg F. In operation, the tube is heated throughout to a uniform 500 deg F. Careful measurement at the higher temperature indicates that the fixed ends separate to 13.008 in. What loads are exerted on the ends of the tube, and what are the resultant stresses?
A solid 45 mm diameter beryllium copper (E = 131 GPa; α = 17.0 × 10−6 /°C) rod is stress free when securely attached to the unyielding supports shown in the figure below. If the compressive normal stress in the rod must not exceed 450 MPa, what is the maximum temperature increase (rounded down to the nearest degree) that can be allowed for the rod? Use L1 = 300 mm.
An aluminum alloy cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The steel [E = 200 GPa; α1 = 11.7 × 10−6/°C] bolts have a diameter of 19 mm. The aluminum alloy [E = 70 GPa; α2 = 23.6 × 10−6/°C] cylinder has an outside diameter of 160 mm and a wall thickness of 9 mm. Assume that a = 700 mm, b = 810 mm, and c = 325 mm. If the temperature of this assembly changes by ΔT = 60°C, determine(a) the normal stress in the aluminum cylinder.(b) the normal strain in the aluminum cylinder.(c) the normal strain in the steel bolts.
a)Find the thermal deformation (in inches) of the steel bolt. (Write your answer to 6-decimal places.) b)Find the thermal deformation (in inches) of the aluminum tube. (Write your answer to 6-decimal places.)c)Find the stress (in psi) induced in the steel bolt by the temperature change.
Mechanics of Materials (Thermal Stresses) A steel rod with a cross-sectional area of 140 mm2 is placed between two fixed supports. The tensile force at 200C is 4000 N. What will be the stress at -150C? Use E = 200 x 103 MPa and α = 11.7 x 10-6/ 0C.
a.) Find the bulk modulus of elasticity of a liquid if a pressure of 150 psi applied to 10 ft3 of the liquid causes a volume reduction of 0.02 ft.3. b.) Find the capillary rise in the tube for a water-air-glass interface (θ = 0°) if the tube radius is 1 mm. Surface tension is 0.0728 N/m.
Strain gage on the surface of a thin-walled steel boiler as shown in the figureaffixed. With shape change meter εx = 500 (10-6A value of) was read. The inner diameter of the boiler 60Mm. The wall thickness of the boiler is 2mm E=200 GPa, υ=0.3 a)Calculate the stresses in the boiler b)Determine the internal pressure in the boiler
A steel rod with a cross sectional area of 180 mm² is stretched between two fixed points. The Tensile load at 25 degrees is 3600 N. Assume α= 11.7 x10^-6 mm/(mm –degree celsius) and E = 200 GPA. Calculate the temperature at which the stress will be zero. Your answer
A steel bar is placed between two copper bars, each having the same area and length as steel bar at 20℃. A this stage, they are rigidly connected together at both the ends. When the temperature is raised to 320℃, the length of the bars increases by 1.5mm. Determine the original length and final stresses in the bars. Steel: Coefficient of expansion = 0.000012/℃; Es = 215 GN/m^2 Copper: Coefficient of expansion = 0.0000175/℃; Ec = 100 GN/m^2