3. Annular Cylinder

Q: hii, thank you for you answer, why cant i use this simple formula that i added in order to calculate…

A: Given: yes this formula can also be used. This formula will also give the same result. The formula…

Q: FIGURE Q2, COORDINATE SYSTEM FOR Q2 100 90 R20 DETAIL S SCALE 2:15 37 100 |

A: We will answer the first question since the exact one was not specified. Please submit a new…

Q: Locate the center of mass of the block in millimeters. Materials 1, 2 and 3 have densities of 2700…

A:

Q: An engine has eight cylinders. It has a bore cross-sectional area of 42 cm2 and a stroke of 10 cm.…

A: The number of cylinders (n) = 8  Area of each cylinder (A) = 42 cm2 L = 10 cm

Q: In a design, A rectangular object is constructed by connecting four points A (4,2), B(-4,1), C(-2,5)…

A: As per given the rectangle is drawn and its reflection object about point (5,5 ) is also drawn

Q: Assuming unit length to be equal to 10 mm, draw the isometric views of objects shown in figure below…

A:

Q: Compute planar density for Ca (101) in nm 2. Round your answer to 2 decimal place.

A: Planar density :  Number of atoms per unit area that are centered on a particular. crystallographic…

Q: dar Grub planar mcchanism to be one. The mumber of degrees of freedom for below mentioned…

A:

Q: А3 size, in mm, is О 210х 297 О 148 х 210 О 297 х 420 О 8.27 х 11.7 O O O O

A:

Q: Find the three deviations of this solid

A: According to the details provided in the question, we need to draw three projection views.

Q: Determine the Xbar and Ybar of the shape seen below. W = 7 in h = 7 in D= 4 in

A: given data - W= 7 in h= 7 in D= 4 in to determine- co-ordinates of the centroid ( x_bar, y_bar)

Q: What

A: Givenmoment about long axis =My

Q: Phonograph Phonograph records are vinyl discsthat rotate on a turntable. A typical record album is12…

A: Given N = 3313 rpm D = 12 inches To find Angular speed Linear speed inches/min

Q: ed planet if the sate tely in a circular orb of the planet. (See

A:

Q: A line RS of 55 mm in length is inclined to HP by 30o and parallel to VP. One of its end points is…

A: RS=55 cm Scale :1 : 10↓     ↓cm   mm Cos 30°=H.755H.7=55xcos30      =47.63 mm Horizontal…

Q: There is a kindof antique bicycle in which the radius of the rear wheel is one-tenth of the front…

A: Rrear=110Rfrontωrear=90ωfrontDistance L=200 feet And L=2πRrear×rotations×RfrontRrear

Q: Calculate the maximum and minimum dimensions for "X" in the figure below.

A: The basic dimension of X is, X=18-12-4X=2 Determine the tolerance for the X, Total…

Q: If the scale of an image is 20"/mm, an object that is 40 arcseconds in angular size will appear mm…

A: The scale ratio of the angular size to the diameter of the object is, Z=20"/mm The angular size of…

Q: s shown in Figure Q1. Dimensions th of 90 MPa. The diameter of the etion at A:

A:

Q: The equation of the unit circle is _______________.

A:

Q: 4. If 6.5 m³ of oil weighs 46,800 N, calculate its density in kg/m³. (a) 285 (b) 258 (c) 82 (d) 734

A: Given : volume of oil , V = 6.5 m3             weight of oil , W = 46800 N To find : density

Q: Determine the following based on the given illustration: a) Area of the Composite figure

A: To determine the area of the composite figure.

Q: show the angle of declination by drawing the figure and write the important results by making the…

A: (a) Defiition: Angle of declination: It is defined as the angle between magnetic axis and…

Q: theta - 33 degrees M1 - 450 Nm M2 = 550 Nm M3 - 650 Nm M3 M2 M

A: M1=450 N-mM2=550 N-mM3=650 N-mθ=33°

Q: position shown in the figure. 4 ft 4 ft 6 ft

A: MCD=500lb-ft

Q: Assuming simple graph of 10 mm grid, draw the isometric views of objects shown in fig 2

A:

Q: Q5 The sheet metal form as shown in Figure Q5 and has a dimension with x, y and z axis respectively.…

A:

Q: A cylinder of 40mm diameter and 50mm axis is resting on a point of its base circle on VP while it's…

A: Given data Diameter of cylinder,= 40 mm axis of cylinder = 50 mm Inclined to VP = 450 Inclined to HP…

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: (ii) the orientations of the major and minor principal planes relative to the left vertical side of…

A:

Q: 2. Draw a) Sectional Front View and b) Top View of the following component. Assume any missing…

A: The view obtained after removing the front half portion of a system is called as front sectional…

Q: For the figure shown, given that: M = 280 N.m %3D t = 9 mm %3D b = 0.8 mm

A:

Q: Q 2/ Draw the views (Front, Side and Top) for isometric figure shown below with limensions. Note:…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Which of these represents the solution for x in 6" = 21?

A:

Q: Q1: Draw the orthographic Projections of given object. 15 20 R20 O REDMI NOTE 9 PRO MAX O AI QUAD…

A: Orthographic Projection is a 2 dimensional projection of a 3 Dimensional object.

Q: Find x and y of the given figure. Make a table of values for each shape and show complete solution.…

A:

Q: A balanced rigid disc mounted on a rigid rotor has four identical point masses, each of 10 grams,…

A:

Q: Adroplet with unknown diameter has an inside pressure of 980 N and outside M2 pressure of 620 M2 N…

A:

Q: Draw isometric view of frustum of the square pyramid with 45 mm base edge, 25 mm upper edge and…

A: ISOMETRIC VIEW OF THE GIVEN PROBLEM IS GIVEN BY AS BELOW

Q: 2. Draw the FBD of each sphere shown below 45mm 200N 500N A B 75mm 200mm

A: Let us draw the FBD, A and B is the reaction force of the wall and N is the normal force of the…

Q: 40 N 40 N 30 B RAX C 5 ft - 5 ft 3 ft RAY 80 N

A: The system is in equilibrium.

Q: Point, Line, and Planes

A: Given Data⇒ Point Line Plane

Q: Find Fi, Fz, Fg magnitude.

A: Write the forces in vector form, F→1=F1×35 j^+F1×45 k^F→1=0.6 F1 j^+0.8 F1 k^F→2=-F2 i^F→3=F3×35…

Q: CHOOSE THE BEST ANSWER. SHOW THE DETAILS OF YOUR SOLUTIONS TO CREDIT THE CHOICE YOU MADE. DRAW THE…

A:

Theory and Design for Mechanical Measurements

Measurement is a term that refers to analyzing a manufactured component regarding the degree of accuracy for dimensions, tolerances, geometric profile, roundness, flatness, smoothness, etc. Measurement always involves comparing the manufactured component or the prototype with a standard specimen whose dimensions and other parameters are assumed to be perfect and do not undergo changes with respect to time.Precisely in mechanical engineering the branch that deals with the application of scientific principles for measurements is known as metrology. The domain of metrology in general deals with various measurements like mechanical, chemical, thermodynamic, physical, and biological measurements. In mechanical engineering, the measurements are limited to mechanical specific such as length, mass, surface profile, flatness, roundness, viscosity, heat transfer, etc.

Basic principles of engineering metrology

Metrology is described as the science of measurement, precision, and accuracy. In other words, it is a method of measurement based on units and predefined standards.