3. Consider the following series RLC circuit where the maximum input voltage is 500 mV. At what frequency, fo, is the amplitude of Var a maximum? What is the Yout value at fo? What is the equivalent impedance as seen by the source at the resonant frequency fo? Over what frequency range will the output power be > 50% of maximum (i,e. BW)? What is the Quality Factor (QF) of the circuit? Sketch the frequency response of the output voltage and highlight the key characteristics. a. b. C. d. е. 15mH 100nF Vs 500 Vout

3. Consider the following series RLC circuit where the maximum input voltage is 500 mV. At what frequency, fo, is the amplitude of Var a maximum? What is the Yout value at fo? What is the equivalent impedance as seen by the source at the resonant frequency fo? Over what frequency range will the output power be > 50% of maximum (i,e. BW)? What is the Quality Factor (QF) of the circuit? Sketch the frequency response of the output voltage and highlight the key characteristics. a. b. C. d. е. 15mH 100nF Vs 500 Vout

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the gain of the following circuit and the lower and upper cutoff frequencies. (RS = 1 kΩ, R1 = 40 kΩ, R2 = 10kΩ, RC = 15 kΩ, RE = 25 kΩ, RL = 2.2 kΩ, CS = 10 µF, CC = 1 µF, CE = 20 µF, Cbe = 20 pF, Cbc = 30 pF, Vcc = 25 VVT = 26mV, β = 100, ro = infinity
Given the parallel RLC circuit below, (a) derive the expression for the resonantfrequency, the half power frequencies, the bandwidth, and the quality factor for the transfer function of Vout/Iin in terms of the circuit parameters R, L and C, and (b) Compute the quantities in (a) if R = 1kohm, L = 10mH and C = 100uF.
a) from the rootlocus fig , Write the open loop transfer function of the system,b) What is the value of K for critical damped response?c) What is the range of K for stable closed-loop system?d) Determine damping ratio and ( Wn ) of the closed loop system for K=10.e) Sketch the approximate graph of the Bode magnitude of the transfer function (use K=100).
The voltage transfer function of the prototype bandpass filtershown isH(s)=(1Q)ss2+(1Q)s+1. Show that if the circuit is scaled in both magnitude and frequency, thescaled transfer function isH′(s)=(1Q)(skf)(skf)2+(1Q)(skf)+1.
In the circuit given in the figure, β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 0.5 kΩ and RL = 53 kΩ. Accordingly, find the voltage gain (Vout/Vin) of the circuit.NOTE-1: The output impedance of the transistor r0 will be taken into account in the calculations.NOTE-2: Capacitors are negligible at midband frequency.NOTE-3: The applied ac voltage has an amplitude of 10 mV and a frequency of 1 kHz.
In the circuit shown in the figure, Vcc = 12 V, Vin = 10 mV, β = 100, r0 = 40 kΩ, RB = 360 kΩ, RC = 3.3 kΩ, RE = 220 Ω, Rs = 0.5 kΩ and RL = 42.1 kΩ . Accordingly, find the voltage gain (Vout/Vin) of the circuit.NOTE-1: The output impedance of the transistor r0 will be taken into account in the calculations.NOTE-2: Capacitors are negligible at midband frequency.
The voltage transfer function for either high-pass prototype filtershown isH(s)=ss+1. Show that if either circuit is scaled in both magnitude and frequency, thescaled transfer function isH′(s)=(s/kf)(s/kf)+1.
(a) Find the bandwidth of the current mirror as shown if I1 = 100μA, CGD = 1pF, and λ = 0.02 V−1. (b) If I1 = 25 μA.
A series RLC circuit is formed using component values R=100 and L=1.5 mH, together with a source that provides a sinusoidal voltage Vs (t). If the quality factor in resonance condition is Q0 = 7, determine: a) the magnitude of the impedance at 500 Mrad s-1b) the current that circulates if vs (t) = 2,5V cos (425 ×10 6t) Note: Vent (input voltage). Vsal (output voltage)
ı just need fınal aswer In the circuit in the figure, Vcc = 18 V, Rs1 = 0.9 kΩ, Rs2 = 0.5 kΩ, R1 = 75 kΩ, R2 = 15 kΩ, RC = 2.2 kΩ, RE = 1 kΩ and β =120. It is also known that Cwi = 6 pF, Cwo = 10 pF, Cbc = Cu = 7 pF, Cbe = Cπ = 58 pF and Cce = 11 pF. Accordingly, considering the frequency response of the circuit, what would be the high cutoff frequency (fH)? NOTE-1: The output impedance of the transistor is r0 = 20 kΩ and will be considered in the calculations. NOTE-2: The high frequency dependence of hfe, that is β, will be taken into account. a. 189,95 kHz b. 617,33 kHz c. 569,84 kHz d. 474,87 kHz e. 332,41 kHz f. 47,49 kHz g. 142,46 kHz h. 712,30 kHz
Obtain the transfer function Vo (s) / Vi (s) for the electric circuit given in the figure.You can find the amplitude value of the transfer function at high frequencies of the circuit.If it works, calculate approximately. System-owned transferDraw the Bode diagram of the function.
Consider the angle modulated signal: v(t) = 10 cos [2πx108t + 3 cos(2πx103t)] Assume that the signal is PM. Find the bandwidth using Carson’s rule of the PM signal when themessage frequency is (a) doubled, (b) halved, but all else remains constant.