3. Determine the nominal compressive strength of a W360 x 44 of A992Gr50 steel column having length of 4 m and is fixed at both ends. (Gr50 steel = 50 ksi = 345 MPa = Fy) Properties of W360 x 44 A = 5710 mm d = 351 mm b,= 171 mm t₁ = 9.78 mm t = 6.86 mm Kdes = 19.9 mm k₁ = 19.1 mm r₂ = 146 mm R, = 37.8 mm

3. Determine the nominal compressive strength of a W360 x 44 of A992Gr50 steel column having length of 4 m and is fixed at both ends. (Gr50 steel = 50 ksi = 345 MPa = Fy) Properties of W360 x 44 A = 5710 mm d = 351 mm b,= 171 mm t₁ = 9.78 mm t = 6.86 mm Kdes = 19.9 mm k₁ = 19.1 mm r₂ = 146 mm R, = 37.8 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An S 380 x 74 section is used as a simply supported beam to carry the uniformly distributed load of magnitude 3W and the concentrated load W. What is the maximum allowable value of W if the working stress in bending is 120 MPa?
The steel beam has the cross section shown. The beam length is L = 7.1 m, and the cross-sectional dimensions are d = 360 mm, bf = 180 mm, tf = 16 mm, and tw = 9 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 185 MPa.
A simply supported beam has a maximum moment equal to 25 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual bending stress of the beam in MPa? Blank 1 (use two decimal places)
Figure Q4 in APPENDIX II shows a cross-section of a rectangular braced column of 200 mm x 300 mm. The column is classified as short column and subjected to ultimate load of 1250 kN. Given bending moments of 55 kNm and 30 kNm about major and minor axes respectively. Use the characteristic strength of concrete, fck = 25 N/mm2, the characteristic strength of steel, fyk = 500 N/mm2, Cnom = 30 mm, the effective length = 4.2 m, ϕlink = 6 mm and ϕbar = 20 mm. (i) Calculate the value of Mmin and MEd.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: Using a T-beam geometry, determine the required amount of flexure bars for maximum ultimate bending. = [As] sq.mm (whole number)
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 20.5 ksi. Assume P = 32 kips, L1 = 2.4 ft, and L2 = 7.2 ft.(a) Determine the minimum section modulus required for this beam.(b) From the table below, select the lightest W shape that can be used for this beam.(c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?
For the wooden beam sketched in the figure, ask for the mid-span section. a) Determine the normal stresses at points 1, 2, 3 and 4. (Represent the distribution of normal stresses in the section) b) Check the structural safety in relation to normal stresses. (Adopting γt = 3.2 and γc = 2.5) ADDITIONAL DATA / INFORMATION Characteristic strengths of wood: TENSION: σr,t = 52 MPa COMPRESSION: σr,c = 40 MPa
A simple beam 4.4 m in span carries a concentrated load of 316 kN at its midspan and is subjected to an axial tensile force of 243 kN. Fy = 248 MPa.Three sections are being considered as follows with their corresponding properties relevant to the problem.Use the formula: (fa/0.60Fy) + (fb/0.66Fy) <1.0 Questions:What is the lowest axial Stress?Hint Answer: 18.69
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 22.9 ksi. Assume P = 34 kips, L1 = 4.2 ft, and L2 = 12.6 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this bear. (c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 40.7 ksi. Assume P = 69 kips, L1 = 2.7 ft, and L2 = 8.1 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this beam. (c) What is the total weight of the steel beam itself (i.e., not including the loads that are carried by the beam)?
The beam shown will be constructed from a standard steel W-shape using an allowable bending stress of 64.5 ksi. Assume P=66 kips, L1=6.1 ft, and L2=18.3 ft. (a) Determine the minimum section modulus required for this beam. (b) From the table below, select the lightest W shape that can be used for this beam (c) What is the total weight of the steel beam itself (l.e. not including the loads that are carried by the beam)?
A normal-weight concrete rectangular beam has dimensions b = 285 mm by h = 634 mm with an effective depth of d = 614 mm and is reinforced with three - 25 mm diameter bars at the bottom of the cross-section. The concrete cylinder strength, f'c = 27.6MPa. The yield point of steel, fy = 414.7MPa. The beam carries a bending moment of 140 kN-m. Modulus of Elasticity of steel, Es = 200GPa. Solve for the following: 1. What is the gross moment of inertia of the section in mm4? 2. Compute the concrete compression stress at the top in MPa. 3. Compute the concrete tension stress at the bottom in MPa. 4. Compute the stress in steel in MPa.