3. Five weights of 10, 20, 30, 40, and 50 N rest on a table with the coordinates (0.5, 15*), (2, 90*), (0.9,190*), (0.5, 260*), and (1.5,340*), respectively, where the first number in parenthesis represents the radial distance in meters from the center of the table and the angle is measured counterclockwise from the reference radius as the table is viewed from above. Determine the location of resultant weight.

3. Five weights of 10, 20, 30, 40, and 50 N rest on a table with the coordinates (0.5, 15), (2, 90), (0.9,190), (0.5, 260), and (1.5,340*), respectively, where the first number in parenthesis represents the radial distance in meters from the center of the table and the angle is measured counterclockwise from the reference radius as the table is viewed from above. Determine the location of resultant weight.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The distance recorded for abaseline was 430.60 using a 100 m steel tapestandardized at 15C and with a standardpull of 10 kg. At the time the temperaturewas measured to be 20C and the pullexerted was 16 kg. Unit weight of steel is 7.86g/cc and weight of steel is 2.67 kg, E =200000 MPa,  = 70 x 10-6 m/C. 1. What is the correction for temperature?a. 0.0082 c. 0.0090b. 0.00097 d. 0.00035 2. What is the pull correction?a. 0.0082 c. 0.0090b. 0.00097 d. 0.00035 3. What is the true length of the baseline?a. 430.6119 c. 430.6214b. 430.6403 d. 430.6505
A 100-ft steel tape of cross-sectional area 0.0025 square inches, weight 2.3 lb, and standardized at 68°F is 99.992 ft between end marks when supported throughout under a 12-lb pull. What is the true horizontal length of a recorded distance AB that is equal to 286.06 m with average temperature of 85°F supported at tape ends only and a pull during measurement equal to 25 lb.
How did you find Hf = 24.5? Also, you went from 112.1 to 142.1?
A steel tape is 100.00 ft long and has a weight of 0.0225 lb/ft and is used to measure a line from A to B in two segments (one full tape length and one partial tape length), supported at the ends only for each of the two segments. The recorded distance is 181.83 ft. The pull at the time of measurement is 12 lb. What is the length of the line corrected for sag? (Assume that no other tape corrections need to be applied.)
Given that: a = 2m b = 3m c = 3m d = 7m e = 2m f = 2m g = 4m h = 6m Windward = 14kPa Leeward = 13kPa Show COMPLETE SOLUTION
Select one: a. 90 kN b. 80 kN c. 70 kN d. 100 kN
3. A 50 m tape weighing 0.03kg/m is used to measure distance AB. The tape is supported at both end points and at its midspan and then applied tension is 6 kg. Determine the total sag correction if the measured distance is 1, 320.50m. 4. A building 38m X 45m is to be laid out with a 50m long metallic tape. If during standardization the tape is found to be only 49.950m, determine the following: a.) Dimensions to be laid out, using this tape, in order that the building shall have the desired dimensions. b.) Using the same tape what should the diagonal reads.
determine the resultant of the following 1. 24m, 25° E of S 2. 30m, NW 3. 45m, 50° N of E 4. 20M, W of S
. You have been given the following constant-head data for planar flow of water in a 1.5-mm thick geotextile that is 300-mm wide by 600-mm long. Calculate the transmissivity in m3/min-m of fabric and then the planar coefficient of permeability in cm/sec. Total head lost, Dh (mm) q (cm3/min) 75 21 150 41 225 60 300 79
3.A civil engineer used a 30m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial point and the end point was found to be 1.25m. The 30m tape is of standard length at a temperature of 10°C and a pull of 50 N. During measurement the temperature reading was 15°C and the tape was supported at both ends with an applied pull of 75 N. The cross-sectional area of the tape is 6.50 sq. mm and the modulus of elasticity is 200GPa. The tape has a mass of 0.075 kg/m. a. determine the total correction per tape length. b. determine the correction for slope. c. determine the horizontal distance.
To measure a base line, a steel tape 30 m long standardized at 15 C under a pull of 10 Kg was used. Find the correction per tape length if the field temperature was 20 C and the pull exerted was 16 Kg. The tape section area was 0.03419
kindly give the solution for this problem where the ans. is 200,000 lb,98,000 lb and 11.17 ft