3. For the A-connected load in the following figure, calculate a) The magnitude and angle of each phase current Ib, Ibe, and Ia b) The magnitude and phase angle of each line current IAa, Ipb, Ice c) The magnitude and angle of voltages EAB, EBC, ECA d) The power supplied by the source and power received at the load 1 k V = 16 kV 0° V. = 16 kV Z-120° 10N 20 N EAR 0.3 kn, 1 kn V = 16 kV Z+120° ca ECA 10Ω 20 Ω 0.3 ki 0.3 kn 1 kn 100 20 N

3. For the A-connected load in the following figure, calculate a) The magnitude and angle of each phase current Ib, Ibe, and Ia b) The magnitude and phase angle of each line current IAa, Ipb, Ice c) The magnitude and angle of voltages EAB, EBC, ECA d) The power supplied by the source and power received at the load 1 k V = 16 kV 0° V. = 16 kV Z-120° 10N 20 N EAR 0.3 kn, 1 kn V = 16 kV Z+120° ca ECA 10Ω 20 Ω 0.3 ki 0.3 kn 1 kn 100 20 N

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.48P

See similar textbooks

Similar questions

It is stated that (i) balanced three-phase circuits can be solved in per unit on a per-phase basis after converting - load impedances to equivalent Y impedances. (ii) Base values can be selected either on a per-phase basis or on a three-phase basis. (a) Both statements are true. (b) Neither is true. (c) Only one of the above is true.
Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
Two three-phase generators supply a three-phase load through separate three-phase lines. The load absorbs 30 kW at 0.8 power factor lagging. The line impedance is (1.4+j1.6) per phase between generator G1 and the load, and (0.8+j1) per phase between generator G2 and the load. If generator G1 supplies 15 kW at 0.8 poir factor lagging, with a terminal voltage of 460 V line-to-line, determine (a) the voltage at the load terminals. (b) the voltage at the terminals of generator G2, and (c) the real and reactive power supplied by generator G2. Assume balanced operation.
A three-phase line with an impedance of (0.2+j1.0)/ phase feeds three balanced three-phase loads connected in parallel. Load 1: Absorbs a total of 150 kW and 120 kvar. Load 2: Delta connected with an impedance of (150j48)/phase. Load 3: 120 kVA at 0.6 PF leading. If the line-to-neutral voltage at the load end of the line is 2000 v (rms), determine the magnitude of the line-to-line voltage at the source end of the line.
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at 0.9 power factor leading, are connected in parallel and supplied by a balanced three-phase Y-connected, 480-V source. (a) Determine the source current. (b) If the load neutrals are connected to the source neutral by a zero-ohm neutral wire through an ammeter, what will the ammeter read?
A single-phase source is applied to a two-terminal, passive circuit with equivalent impedance Z=3.045, measured from the terminals. The source current is i(t)=22cos(t)kA. Determine the (a) instantaneous power, (b) real power, (c) reactive power delivered by the source, and (d) source power factor.
single circuit three-phase line, 60 Hz, 18 km has a total resistance and inductive reactance of 4.242 ohm and7.451 ohm per phase respectively. The line delivers 2500 kW to a balanced load at 11 kV. (1) determine the sending-end voltage when the power factor is (i) 80% lagging, (i) unity, and (ii) 90 % leading, (2) draw the phasor diagrams of the line at the above (3) determine the voltage regulation of the line at the above power factors.
A three-phase transmission line has an impedance of 2 + j8 Ω per phase. The linesupplies the following two three-phase loads:Load 1: 600 KVA at 0.8 power factor lagging.Load 2: 300 KVA at 0.9 power factor lagging.The phase voltage at the loads is Vr = 2000∟0◦ volts.Determine:a) The phase voltage at the sending end (Vs).b) Three-phase real and reactive power losses in the transmission line.c) Three-phase real and reactive power supplied at the sending end.
A three phase, 60 Hz, 60 km long transmission line has series impedanceZ=0.1+ j 0.5Ω/ km delivers 40 MVA at 48 kV to a load at its receiving end at 0.9 power factor leading. Find the following1. ABCD parameters2. Sending end voltage and current3. Sending real and reactive power 4. Power factor at sending end5. Voltage regulation6. Efficiency PLEASE EXPLAIN THE PHASOR MULTIPLICATION. THANK YOU
A 400V three-phase, four wire system has the following loads connected: Phase 1: load impedance Z1 = 40 + j15 Ω Phase 2: load impedance Z2 = 60 Ω Phase 3: load impedance Z3 = 15 – j20 Ω I am just looking for the working out for phase 2 - please ignore the other phases The line and phase voltages for all phases (including phase angles) The line and phase currents for all phases (including phase angles) The neutral current (including phase angle)
1. A 69-kV, three-phase short transmission line is 16 km long. The line has a per phase series impedance of 0.125+j0.4375 Ω per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers (a) 70 MVA, 0.8 lagging power factor at 64 kV. (b) 120 MW, unity power factor at 64 kV. Use lineperf program to verify your results. 2. A three-phase, 765-kV, 60-Hz transposed line is composed of four ACSR, l,431,000-cmil, 45/7 Bobolink conductors per phase with flat horizontal spacing of 14 m. The conductors have a diameter of 3.625 cm and a GMR of 1.439 cm. The bundle spacing is 45 cm. The line is 400 km long, and for the purpose of this problem, a lossless line is assumed. (a) Determine the transmission line surge impedance Zc, phase constant ß, Wavelength, the surge impedance loading SIL, and the ABCD constant. b) The line delivers 2000 MVA at 0.8 lagging power factor at 735 kV. Determine the sending end quantities and…