3. For the circuit on the right, assume that Ic= 1mA, and the transistor is in the active mode (R₁ = Rs = 1kn2, B = 100). a- Draw the small signal model and calculate the transistor parameters such as gm and r. b- Calculate the input and output poles of the transistor if C₁ = Cu = 10:¹2 Farads. Vinº Rs ww

3. For the circuit on the right, assume that Ic= 1mA, and the transistor is in the active mode (R₁ = Rs = 1kn2, B = 100). a- Draw the small signal model and calculate the transistor parameters such as gm and r. b- Calculate the input and output poles of the transistor if C₁ = Cu = 10:¹2 Farads. Vinº Rs ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem: Fx=(AB+CD+EF+G)' a. Draw its equivalent transistor circuit. b. Determine if the function has an Euler's path. please draw the equivalent Euler's path. C. Whether the circuit has a Euler's path or not, draw the stick diagram.
Answer as quickly as possible. I'll give upvote. Thank you. The circuit shown is a common source amplifier with a current mirror bias. It is given that the NMOS (M1) parameters are μoCox = 3mA/V2, VTH,n = 0.5V and λ = 0.02 and the PMOS (M2 and M3) parameters are μoCox = 1mA/V2 and VTH,p = −0.6V . The PMOS transistor M3 does not have channel length modulation while PMOS transistor M2 has λ = 0.02. It is also given that the dimensions of M2 and M3 have equal widths of 5µm and lengths of L2 = 3µm and L3 = 1.5µm, respectively. M1 has length of L1 = 1µm and width of W1 = 2µm. Find the gm and ro of transistor M1.
Design and find output signal in the common emitter voltage divider Rs-0.5k.Rc-4.9K,Re-0.5K, RL=50K, and C1=C2=CE=luF. circuit if we have Vcc = 10V, R1=50k, R2=10K, Assume Vin=7mV with 1KHz
Consider a CE circuit, where trans-conductance is 50mΩ-1, diffusion capacitance is 100 pF, transition capacitance is 3 pF. IB = 20μA. Given base emitter dynamic resistance, rbe = 1000 Ω, input VI is 20*sin(107t). What is the short circuit current gain?
Vi=20mV , Vcc=15V ,β=110 , r0=30kΩ , Rc=4.7kΩ , RF1=100kΩ , RF2=47kΩ AC source internal resistance Rs = 1.34kΩ , load RL=9,1kΩ output voltage V0 =? Note : Output impedance of transistor r0 must be taken into account in calculations
In the circuit in the figure, VGSQ = 6.8 V, IDQ = 2.4 mA, VGS(Th) = 3.3 V, k = 0.4x10-3 A/V2, RD = 5.6 kΩ, RF = 2.2 MΩ and rd = 25 kΩ. Accordingly, when a RL = 23.6 kΩ load is connected to the output of the circuit, what will be the voltage gain of the circuit? NOTE: MOSFET output resistance must be taken into account in rd calculations.
If VCC=10V, RB1=12kΩ, RB2=4kΩ, RC=2kΩ, RE=1kΩ, VBE=1V, hfe=300, VT=26mV, CS=1uF, CE=5uF in the circuit below, then C1 is required for the circuit to oscillate at 200kHz. What should the values of , C2 and L be?
2. a) Design a 9v DC oscillator circuit that produces a frequency of 500 Hz. The circuit may use a 555 timer or two transistor design(s). Show all calculations including the DC currents and bias voltages. Include the schematic and the required frequency formula(s). b) As a bonus, if a larger load were required to be connected to the chip, how would the schematic look and what components would be used to do design it? Also, as a theoretical approximation, if the 9v battery had a rating of 4 amp-hours, how long would it last powering this circuit? Show calculations to illustrate how you arrived at the answer.
Answer ASAP. I'll upvote. Thank you. Given: The circuit shown is a common source amplifier with a current mirror bias. It is given that the NMOS (M1) parameters are μoCox = 3mA/V2, VTH,n = 0.5V and λ = 0.02 and the PMOS (M2 and M3) parameters are μoCox = 1mA/V2 and VTH,p = −0.6V . The PMOS transistor M3 does not have channel length modulation while PMOS transistor M2 has λ = 0.02. It is also given that the dimensions of M2 and M3 have equal widths of 5µm and lengths of L2 = 3µm and L3 = 1.5µm, respectively. M1 has length of L1 = 1µm and width of W1 = 2µm. Sketch the small signal model of transistor M3 (Hint: Is there any small signal in any terminal ofM3? If yes, then where is it? If no, then what happens to the small signal model?).
Using 741 op amp, design a suitable circuit to generate Binary Phase Shift Keyiing(BFSK) modulator. Design should perform in such a way that the BFSK output should contain a frequency of f1=2kHz when message signal is low and f2 =4kHz when the message signal is high. Take the frequency of message signal as 200Hz. Draw the clear circuit diagram and calculate the values of resistors and capacitors used.
answer all A - Explain the relation of MOSFET input current and input impedance and their effect on the functionality of the device. B- Explain how to increase the efficiency of the solar cells (PV cells) through the integration of antennas. C- List three conditions need to be considered to choose a MOSFET for switching applications.
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?