3. Perform the following steps for the given circuit in below.a) Find the fLS, fLC and fLEb) Calculate the Av for the medium band frequencyc) Calculate the values of fHl and fHO cut-off frequencies.Vcc = +20V%3DCw1 = 7pFCw2 = 3pFCbe = 2pFCce = 6pFCbe = 33pFRcP4.7kQ33kΩCc- V.B =1200.5µFRsCsHElµF0.6k2RL.'10kΩ3.3k- 2k240µFVi = Vs =2mV, rms

(a) Calculating different frequencies VE=VB-0.7=1.8-0.7=1.1 V Ri = R1 || R2 || βre Ri=0.49 kΩ…

3. Perform the following steps for the given circuit in below. a) Find the fL.S, fLC and fLE b) Calculate the Av for the medium band frequency c) Calculate the values of fHỈ and fHO cut-off frequencies. Vcc = +20V Cw1 = 7pF Cw2 = 3pF Cbc = 2pF Cce = %3D %3D 6pF Cbe = 33PF Rc 4.7kQ %3D 33kΩ Cc HE B =120 0.5μF Rs C: HE 0.6kQ 1µF RL. 3.3kN. 2kQ 40µF Vi = Vs =2mV, rms

3. Perform the following steps for the given circuit in below. a) Find the fL.S, fLC and fLE b) Calculate the Av for the medium band frequency c) Calculate the values of fHỈ and fHO cut-off frequencies. Vcc = +20V Cw1 = 7pF Cw2 = 3pF Cbc = 2pF Cce = %3D %3D 6pF Cbe = 33PF Rc 4.7kQ %3D 33kΩ Cc HE B =120 0.5μF Rs C: HE 0.6kQ 1µF RL. 3.3kN. 2kQ 40µF Vi = Vs =2mV, rms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Tuned Circuit Design Using a VARICAP (a) Refer to the capacitance curves for the Motorola 1N4002 The input tuning circuit of a standard analog FM radio is given below. Specify, that is design for, a voltage, capacitance, and inductance required to tune the circuit to the center frequency of KUMD-FM which operates at 103.3 MHz. Sketching and labeling a representative resonance curve is required to support your calculations. There is no single correct design answer set of values since it depends upon the voltage you initially select to tune your diode.
Given the following: VCC = 15V C1= 1uFhfe =150 hie = 1.08 kΩR1 = 100kΩ C2 = 220uFR2 = 20 kΩ C3 = 0.32 uFRC = 2 kΩ Cwi = 12pF,Cwo = 10pF RE = 500 Ω Cbe = 15 pF Cbc = 25pFRL = 2 kΩ Determine the following: Midband gain Av Midband Total Voltage Gain AvT Midband Total Current Gain AiT
The circuit show in figure has fr=200MHz, Cbc=1pf, Cbe=50pf, 1rbb=0 and rbe=1kohm. Derive an expression for Av=Vo/Vs at high frequency and find the value of effective fH
2. Prove that , for a radio receiverOutput SNR in dB = Input SNR (dB) - Noise Figure(NF)[You can start the derivation from the relation connecting Noise Figure (NF)and Noise Ratio(F) ] note: the answe will be by hand written.
Discus the Time Response Analysis and the Frequency Response Analysis. Discuss the Bode plot and Nyquist (Polar) plot to estimate the system stability and comment.
Sketch the Vout/Vin versus frequency characteristics of an LC Bandpass filter. Show flc and fhc on the sketch and explain how they are defined. On this sketch, show the bandwidth (BW) of the filter and explain how it is defined.
Q2 (B) Given m(t) = sin 2000 πt, kf = 200,000π, and kp = 8000 π.Find frequency deviation, Δf, for(i) Frequency Modulated (FM) signal(ii) Phase Modulated (PM) signal.
A 10 MHz TXCO is driving a receiver’s front end and has a frequency deviation of 4 ppm. It drives a direct down conversion RF front-end mixing the L2 frequency. What is the frequency offset at baseband due to the TXCO?
help please with explain A narrowband FM signal has a carrier frequency of 110 kHz and a deviation ratio of 0.05. The modulation bandwidth (signal bandwidth) is 10 kHz. This signal is used to generate a wideband FM signal with a deviation ratio of 18 and a carrier frequency of 98 MHz. a) Give the required value of frequency multiplication, n. b) Give two frequencies for the mixer to give the desired carrier. c) Define the required bandpass filter (center frequency and bandwidth).
What can you say about the impedance of a parallel RLC circuit at the resonant frequency? How is the resonant frequency defined? Compare the definition of quality factor for the parallel resonant circuit with that for the series resonant circuit.
An FM signal has a maximum frequency deviation of 1500h and a modulating frequency of 500h, its total power is 6500w, applied to a resistive load of 1ohm, the carrier frequency is 400Mhz. Determine the sensitivity of the modulator, and the magnitude spectrum
For the given circuit, derive the transfer function vo/vi and show how to determine the location of the pole and zero frequencies.