3. Shown in the accompanying sketch are the measured offsets from a traverse line AB to an irregular boundary and the spacing between the offsets. Find the area using: a) Mid Ordinate Rule b) Average-ordinate Rule c) Trapezoidal Rule d) Simpson's Rule

3. Shown in the accompanying sketch are the measured offsets from a traverse line AB to an irregular boundary and the spacing between the offsets. Find the area using: a) Mid Ordinate Rule b) Average-ordinate Rule c) Trapezoidal Rule d) Simpson's Rule

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A parcel of land has been surveyed in the field and the lengths and bearings of the various sides…

Q: The observed angles of a quadrilateral are given in the table below: Angle DBA Value 30 49 59 20 CBD…

A: A quadrilateral angle CBD,DBA,BCA and AC/DC have been given in the question and it has been asked…

Q: The data from a closed traverse ABCD are given in the table below: Line Included angle (in degrees)…

A: Given data,

Q: A line AC cannot be measured directly because of an obstruction on line. Accordingly, the two lines…

Q: Elementary Surveying: Measurement of Horizontal Distances, show proper and right solution. 1. A…

Q: The given table shows the data for a certain closed traverse: Line Distance (m) Bearing AB N55°W BC…

Q: If the distance between points (A) and (B) is ( 125 m) and these points have difference elevations (…

A: h=0.5m L=125m

Q: Calculate the side widths and cross-section area of embankment having width =20m and side slope( 1/2…

A: width of the embankment B= 20m side slope ratio (height : width)=1/2 or 1:2 height of the…

Q: A closed traverse of a triangular lot is tabulated as shown. LINES BEARINGS DISTANCE АВ N 60°30'W…

Q: Using transit rule, adjust the closed traverse.Compute also the linear error of closure and the…

A: This approach was created to balance a traverse in which the angles are determined with more…

Q: A closed traverse has the following data: Distance Line Bearing Latitude Departure (m) 1081 S…

A: LINE DISTANCE BEARING LATITUDE=Lcosθ DEPARTURE=Lsinθ AB 1081 S73°47'E -301.89 +1037.03 BC…

Q: 8. The following are offsets measured from a random line to a curve boundary 9.6, 12.4, 5.8, 7.0,…

Q: USING THE TABLE BELOW DETERMINE THE FOLLOWING USING COMPASS RULE AND DMD METHOD LINE LENGTH,m…

Q: 3. A closed traverse has the following data LINE XY YZ ZX LENGTH 126 m 233 m 170 m BEARING N 35d E S…

Q: The following offsets were taken from a survey line to an irregular boundary line. (see image)…

Q: Q.1: A tract of land has three straight boundaries AB, BC, and CD. The fourth boundary DA is…

A: Straight boundaries are AB, BC and CD Irregular boundary is DA AB = 135 m BC = 191 m CD = 126 m BD =…

Q: A line AB cannot be measured directly because of an obstruction on line, Accordingly, the two lines…

Q: A surveyor uses an auto-level instrument to calculate the length of the sides of a traverse…

A: The formula to calculate the horizontal distance is given by, D=KS+C Here, K is the multiplying…

Q: 6. The slope measurement between two points is 36.225 m and the slope angle is 1°50'. Compute the…

Q: 0. A closed traverse has the following data: Lines Azimuth Distances N 60°30' W N 80°30 E AB 68.75…

Q: 6. Three points A, B, C are marked on the centerline of a roadway. Line AB has an upward slope of…

A: Option (b) is most appropriate.

Q: If the surveyor is at Point A, and recorded the location of Line AB to be 200 degrees 35 minutes in…

A: Bearing of Line AB in WCB = 200°35' Bearing of line AC in WCB = 280°15' Length of line AB= 530.68…

Q: 7. A baseline measures 25 km at elevation 520 m. If the average radius of curvature is 6400 km,…

Q: A: The following angles were measured while surveying a closed traverse ABCD in a clockwise…

Q: - A closed traverse has the following data: Line Distance (m) Bearing AB N40°E ВС Due South СА 1000…

Q: Using a table, provide and differentiate at least three (3) advantages and three (3) disadvantages…

Q: 2. Clockwise interior angles observed in a closed loop traverse is given below: A 83° 30' 251° 50' C…

A: To find the closing error and adjust the angles

Q: Slope distance AB measures 550.65 m and the difference in elevation is 170.24 m for points A and B.…

Q: A closed traverse has the following data: Lines Azimuth Distances (m) N 60°30' W N 80°30' E АВ 68.75…

Q: АВ 33.48 N 73°23' E BC 8.11 S 39°30' E CD 39.42 S 43°40' W DE 7.08 N 39°50' W EA 22.02 N 17°33' W

Q: a) What is the contour interval? b) What is the lowest elevation? c) What is the highest elevation?…

Q: Include the solution and the sketch of the traverse. What is the angular misclosure of a six-sided…

Q: Given the following level section notes for stations 1+160 and 1+180: 1+160 a) What is the roadbed…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: From the given data of a closed traverse, compute the following: a) Find the bearing of Line DA b)…

A: Answer: Length and bearing of line DA can be founded by latitude and departure.So first let us…

Q: A closed traverse has the following data: Lines Azimuth Distances (m) АВ N 60°30' W 68.75 BC N…

A: Given; θ1=N60°30' Wθ2=N80°30' EAB=68.75BC=125.90 Consider the free body diagram as;

Q: Calculate the side widths and cross-section area of embankment having width =20m and side slope( 1/2…

A: width of the embankment (B) = 20m side slope is in the ratio 1:2 height of the embankment= formation…

Q: A closed traverse has the following data: LINE LENGTH (m) BEARING АВ 430.05 N 62°30' E ВС 425.18 S…

Q: The areas in cut of two irregular sections 65 meters apart are 36m2 and 72m2 respectively. Base…

Q: Q2: A five-sided field traverse has the following balanced angles: A = 101°28′26"; B=102°10'42"; C =…

A: Part B Bearing of EA= N20°20'20''W = 339°39'40'' AE= 159°39'40''= S 20°20'20''E…

Q: SHOW COMPLETE SOLUTION IN SOLVING A AND THE AREA 1. a. Find the length r and p of the missing sides…

A: DMD of a line = DMD of previous line + Departure of previous line + Departure of present line. In…

Q: Find the area of the traverse using Simpson's rule if d= 12 m and the values of * offsets are 2.25m,…

Q: From the given data of a closed traverse, compute the following: a) Find the bearing of Line DA b)…

Q: A closed traverse has the following data. Find the bearing of line AB and BC.

A: Given data, Length of line AB= 60m BC= 72.69m CD = 44.83m DE = 56.45m EA = 50m To find out the…

Q: The following are bearings and distances taken on a closed traverse. PROBLEM 1: Bearing N60°E Due…

A: As per the angles given, the traverse is a equilateral triangle.

Q: 1) Using transit rule , adjust the closed traverse.Compute also the linear error of closure and the…

A: Adjustment of Traverse by Transit Rule Latitude = Lcosθ Departure = Lsinθ Correction in LAT =…

Q: The interior angles of a quadrilateral are as follows: Angles Value No. of Measurements A 92 2 B B…

Q: Fundamentals of Surveying: Please show your solution. 6.) Compute the distance (in meter, along the…

Q: For the given data of a close traverse, determine the missing bearings of courses DE and EF then…

A: The bearings of various lines can be determined from the bearing of the known line (generally,…

Q: A traverse has the following data: DRAW THE TRAVERSE AND SOLVE THE FOLLOWING USING COMPASS RULE.…

A: Engineers use information such as lengths and angles between points and lines to determine how to…

Concept explainers

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.

Question

12.30m
irreguler
Boundary
10.80m
7.90m
7.50m
6.40m
6.20
2.70m
-Troversd Line AB
6.0
*6.0
6.0
60
6.0
6.0
6.0
48 0m

3. Shown in the accompanying sketch are the measured offsets from a traverse line AB
to an irregular boundary and the spacing between the offsets. Find the area using:
a) Mid Ordinate Rule
b) Average-ordinate Rule
c) Trapezoidal Rule
d) Simpson's Rule

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Mid ordinate rule

VIEW

Average ordinate, Trapezoidal, Simpson

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the sketch ATTACHED, determine the horizontal distance AB and the elevation of Point B Starting Elevation at A is 50.00’ S (slope dist.) = 822.48 feet, Z (zenith angle) = 88º, hi = 5.15’, r = 5.00’
The following perpendicular offsets were taken from a chain line to an irregularboundary line: (Hint: Use coordinate method)Chainage(m)—0–6.5–16.2–27.2–39.6Offset (m)—3.50–4.75–5.20–6.30–7.36
A series of perpendicular offsets are taken from a transit line to a curved boundary line. These offset were taken 8 m apart band were taken in the following order. 0, 1.5 m, 3m, 3.2m, 4.0m, 5.5 m, 8 m, 4.5m, 3.1m, 1.0m, 0. Using Simpson's one third rule, determine the area included between the transit line ang the curved line using this formula.
Civil engineering ( Survey): An equilateral triangle plot ABC is surveyed with compass in clockwise route. The fore bearing of line AB is 100°. discover the bearing of line BC and CA.
A series of perpendicular offsets were taken from a transit to a curved boundary line. These offsets were taken 9 meters apart and were taken in the following order: 2m, 3.2m, 4m, 3.5m, 5m, 4.5m, 6m, 7m. Determine the area using Trapezoidal rule.
By the trapezoidal rule, find the area between a traverse line and a curved boundary, rectangular offsets being taken at intervals of 5 meters, and the values of the offsets being h1 = 3.2, h2 = 3.4, h3 = 12.8, h4 = 11.2, and h5 = 4.4.
Answer the subquestions: A. A slope measurement of 545.38 m is made between points A and B. The elevation of A is 424.25 m and that of B is 459.06 m. Determine the horizontal distance between two points. B. A traverse line was measured in three sections: 295.85 m at slope 8°45’, 149.58 m at 4°29’, and 373.48 m at slope 4°23’. Determine the horizontal length of the line. Note: Draw the figure and show the complete solution. Provide a recheck of the answers.
determine and draw the baseline using: a. straight line method b. fixed based method using N=5 c. variable slope method
A two-level section has the following data:bottom width=8m side ,slope=2:1 on the left ans 1:1 in the right,transverse slope of the ground=8:1.Find the area of the section if the height at the center is 35% of tge formation width
A closed five-sided field traverse has the following interior angles: A = 121°13′00″; B = 136°44′30″; C = 77°05′30″; D = 94°20′30″. Find the angle at E.
The area in square meters bounded by the contour line of a mountain are as follows: A1 = 5250 A2 = 6900 A3 = 7750 A4 = 8350 A5 = 10250 If the contour interval is 10 m., compute the volume of cut and fill to grade the area at theelevation of A3.
In the quadrilateral ABCD the sides were measured as follows: AB, 8.34 m; BC 7.77 m; CD, 8.99 m; and DA 14.83 m. If the angle between sides AB and BC is 117.85 degrees, determine the area of the quadrilateral. PLEASE NEED ANSWER IN 10 MINS. SORRY BUT IT HAS NO DIAGRAM PRESENTED.