3. There is an abnormal gas in the cylinder. It is compressed from a volume of 300 (liters) and a pressure of 0.1 MPa to a volume of 1000 and a pressure of 0.7 MPa. When the state of the gas can be described by the relation of'PI = constant', find the value of n and the work done by the gas (kJ).

3. There is an abnormal gas in the cylinder. It is compressed from a volume of 300 (liters) and a pressure of 0.1 MPa to a volume of 1000 and a pressure of 0.7 MPa. When the state of the gas can be described by the relation of'PI = constant', find the value of n and the work done by the gas (kJ).

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 6RQ: One British thermal unit will raise the temperature of _____ 1b of water _____F.

See similar textbooks

Related questions

Q: Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

Q: sider two systems A and B. System A contains 3000 kJ energy at 20oC, whereas system B contains 200…

A: To determine the direction of heat transfer when they are brought in contact with each other.

Q: 3. 16.9 N/cm² is the pressure acting at the center of the pipe. Find the force exerted by the oil…

A: Force exerted by the oil upon the gate valve is F = 2.124 MN. Location of the force exerted by the…

Q: The volume of the passenger compartment of an aircraft is 2100 m³. A piece of automatic equipment…

Q: Q2. ( -- Hydrogen gas has a pressure of (500KN/m2), volume of (0.02 m3) and a temperature of (30 C)…

A: Givenppressure P=500kN/m2volume V=0.02m3temperature T=30Co=303KR=0.29kJ/kgK

Q: Air in the 10 m3 tank has a pressure of 500kPa and temperature of 400C. Determine the mass of the…

A: GIVEN DATA PRESSURE P=500KPa VOLUME V = 10m3 TEMPRATURE T=400'C WE HAVE TO FIND MASS OF AIR

Q: Assuming compression is according to the law PV = constant. Calculate the initial volume of gas at a…

A: Given data: P1=2 barP2=42 barV2=2 m3 Need to determine the initial volume of gas.

Q: Q2: The pressure of water flowing through a pipe is measured by the arrangement shown in Figure Q.2.…

A: Given data To find pressure in the pipe .

Q: For a constant volume process, pressure of an ideal gas becomes three times. Calculate the final…

Q: The pressure of the high altitude chamber is 40 m³. It is put into operation by reducing pressure…

A: Given data: The volume of the chamber, v = 40 m3. The initial pressure, P1 = 1 bar. The final…

Q: In a piston-cylinder assembly, there is initially 2 kg of water at a temperature of 25 °C and a…

A: Write the given data:

Q: Water having a mass of 500 Ib is cooled from 70°F to a final temperature of 32°F. Calculate the…

A: Given:m=50 lbT1=70°FT2=32°F

Q: 4) A rigid tank contains 10 kg of water at 90°C. If 8 kg of the water is in the liquid form and the…

Q: Find the specific volume of air having 90°F and 15 psi condition. c. 15.57 ft/lb a. 11.57 ft/lb b.…

Q: 3. Find the density of an oil filled in the liquid column as shown in figure. Given that absolute…

A: GivenPabs=500kpaPatm=1.0132barX=4mY=4mZ=2.25m

Q: Solve the following with diagram

A: Given data: Mass of the piston(m)=4.3 Kg Cross Sectional…

Q: A refrigeration system uses R 12 as the refrigerant. The system is evacuated, then charged with…

Q: A tank contains 80 ft3 of air at a pressure of 350 psi; if the air is cooled until its pressure and…

Q: Q2: The pressure in an automobile tire depends on the temperature of the air in the tire. When the…

Q: Steam is held in two compartments (A and B) separated by a membrane. The total volume is 777 ft, and…

A: Answer: The original specific volume in compartment A is 15.8 ft3/lbm.

Q: A vessel of cylindrical shape is 50 cm in diameter and 75 cm high. It contains 4 kg of a gas. The…

A: Given Data: Mass of gas, m=4 kg

Q: A mass of gas has a temperature of 150°C and volume of 0.2 m3. The temperature is changed to 50°C…

A: Given data: Initial condition: T1=150°C=150+273=423KV1=0.2m3 Final condition:…

Q: 4. A beer barrel has a mass of 10 kg and a volume of 20 liters. Assuming the density of beer is 1000…

Q: Find the radius of a closed cylinder filled with a 500 g liquid that has a bottom pressure measured…

A: unit of pressure is kg/m2 and not kg/m3.

Q: The pressure of the high altitude chamber is 40 m^3. It is put into operation by reducing pressure…

A: Given data: The volume of the chamber, V = 40 m3. The initial pressure, P1 = 1 bar. The final…

Q: 1. Determine the other properties of the steam for the following conditions

A: Dear Student As per guidelines i am allowed to solve first question only ( incase of multiple…

Q: In a closed system, some water is heated to 50 oC. Then it is taken the air by vacuum in the system.…

A: A closed system in the thermodynamics is a system in which there is no transfer of mass occurs in or…

Q: In the automobile tire we usually measure the pressure using a pressure gage, the air in the tire…

Q: THERMODYNAMICS Prob 1. A piston weighs 4.3 kgs and has a cross sectional area of 450 mm2. Determine…

A: Prob 1: Given Data: The mass of the piston is m = 4.3 kg. The cross-sectional area is A= 450 mm2.…

Q: Calculate the pressure that exists inside a 400-L cylinder containing 80 kg of CO2 at 50 ° C.…

Q: Please check attach file

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Oxygen used in oxy-acetylene metal cutting was stored in a tank (empty tank weight is 20lb) whose…

A: Given: To determine the final weight of the tank after the operation.

Q: Q6: Which of the following is not a property of the system ? * O (a) Temperature O (b) Pressure O…

Q: A rigid tank contains 15 kg of water at 75°C. If 3 kg the water is in the vapor form and the rest is…

Q: The pressure of the high altitude chamber is 40 m³. It is put into operation by reducing pressure…

A: Given data: The volume of the chamber, V = 40 m3. Initial pressure, P1 = 1 bar. Final pressure, P2…

Q: 2. The unit weight of water at 50 °F is 62.4 pef. If the volume of the vessel that contains water is…

A: Answer: (a) The change in volume when it is heated to 160°F is 0.080328 ft3. (b) The percentage…

Q: (a) A car with a mass of 850 kg is moving to the right with a constant speed of 1.44 m/s. What is…

A: According to the Newton Second Law of motion , Force is equals to the acceleration and mass of the…

Q: During the process of raising steam in a boiler, when the pressure was 1.9 bar gauge the temperature…

Q: The system in the figure below is at 20 °C. If the pressure at point A is 2900 lb/ft2, determine the…

A: To find pressure at point B,C,D

Q: 3.) The system in the figure below is at 20 °C. If the pressure at point A is 2900 lb/ft², determine…

Q: A piston cylinder device which is designed to perform an isobaric process contains 1-lb of hydrogen…

Q: An unknown mass and a 12 kg mass are tied to a light string and hung over a frictionless pulley. If…

Q: 120 kPa. Calculate the work done by the gas on the remains constant. The initial pressure of the gas…

Q: Gas in enclosed cylinder with a weighted piston as the top boundary. The gas us heated and expands…

Q: A man is pushing a cart that weighs 100 lbf with its contents up a ramp that is inclined at an angle…

A: Given data:

Concept explainers

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

One British thermal unit will raise the temperature of _____ 1b of water _____F.
If some heat is transferred to the gas and its volume is doubled, do you expect the pressure inside the cylinder to change?
The pressure of the high altitude chamber is 40 m^3. It is put into operation by reducing pressure from 1 bar to 0.4 bar and temperature from 25°C to 5°C. a) How many kg. of air must be removed from the chamber during the process? b) Compute the volume at this mass measured at 1 bar and 25°C
Oxygen used in oxy-acetylene metal cutting was stored in a tank (empty tank weight is 20lb) whose volume is 45ft3. Initially, the gauge pressure reading of the tank was 30psi. After usage, the pressure reading falls to 15psi. Determine the final weight (lb) of the tank after the operation if the temperature in the tank remains constant at 75 degrees F.
If a vessel that contains 3.500ft^3 of water at 50 °F and atmospheric pressure is heated to 160 °F a.) what will be the percentage change in its volume? b.) What weight of water must be removed to maintain the original volume
Calculate the Specific Volume at a temperature of 47.3 ° C for a pressure of 0.06 MPa.
: A mass of gas has a temperature of 150°C and volume of 0.2 m3. The temperature is changed to 50°C but the pressure is unchanged. Determine the new volume.
In a piston-cylinder assembly, there is initially 2 kg of water at a temperature of 25 °C and a pressure of 100 kPa. Then heat is given to the water until its volume is 0.4 m3. At this point, the piston in the cylinder is fixed with a stopper, but the water in the cylinder continues to heat until its temperature reaches 300 oC. According to this, calculate a) the final pressure of the water, b) the amount of heat given to the water, c) the work done by the piston. d) Show these processes in the T-v (Temperature-Specific Volume) diagram
7. An air bubble rises from the bottom of the well where the temperature is 20°C to the surface where the temperature is 50°C. If the existing atmospheric pressure at the surface of the well water is 101.3kPa, determine the percent increase in volume of the bubble if the pressure in the bottom of the well is 200kPag. Draw a figure or FBD that will support the problem. Explain each step by step formula.
The hot-air balloon contains air having a temperature of 180∘F while the surrounding air has a temperature of 60∘F The densities of air at 180∘F and 60∘F are 0.00193 slug/ft^3 and 0.00237 slug/ft^3, respectively. The volume of air the balloon contains is 130(10^3) ft^3. The empty weight of the balloon is 300 lb. Determine the maximum weight of the load the balloon can lift.
the initial volume and temperature was 75 liters and 27 degrees respectively. if the final volume is 180 liters, calculate the temperature.
20 mins left help me !! A piston cylinder arrangement contains 100 liters of saturated water and 900 liters of saturated steam in equilibrium at 1 Mpaa. Heat is added at constant pressure until the temperature becomes 300 C. determine the a) The initial Temperature b) the total mass c) the quality of vapor at initial condition d) the final volume e) the work done during the process