30 If the total deformation of the compo site rod in the figure is limited to 0.90 mm, compute the maximum value of "P" that is safe for the composite rod. 3P BRONZE A = 450 mm² L = 0.6 m E = 83 GPa P ALUMINUM A = 600 mm² L = 1.0 m E = 70 GPa 4P STEEL A = 300 mm² L = 0.8 m E = 200 GPa 2P

30 If the total deformation of the compo site rod in the figure is limited to 0.90 mm, compute the maximum value of "P" that is safe for the composite rod. 3P BRONZE A = 450 mm² L = 0.6 m E = 83 GPa P ALUMINUM A = 600 mm² L = 1.0 m E = 70 GPa 4P STEEL A = 300 mm² L = 0.8 m E = 200 GPa 2P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Torsion A square beam of size 400 mm x 400 mm is subjected to a factored bending moment and twisting…

Q: Calculate: AMax using virtual work method.

A: The maximum deflection of beams occurs where slope is zero. Slope of the beam is defined as the…

Q: What is the vertical reaction at support A? A. 35.81 kN B. 46.31 kN C. 50.90 kN D. 51.33 kN What…

A: Detailed solution is attached below as

Q: Consider a Design-and-Build project of a single-entrance toll plaza awarded to XYZConstruction Corp.…

A: The following is the given information. The present travel demand along the existing highway is…

Q: An u.dl of 20 kN/m is acting on cantilever beam of length 3.0 m calculate the slope and deflection…

A: To find slope and deflection at free end of cantilever beam L=3m W=20kN/m Value of E is not…

Q: Calculate the support reactions of the following beams. Also draw the shear and moment diagrams

A: Given data in question UDL 35 KN/m Span 10m To find out Reactions SFD BMD

Q: 5 A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and…

Q: A rectangular concrete beam 120 x 300 mm is prestressed by straight cable, effective force 180 kN at…

A: Given:- Rectangular concrete Beam 120×300 mm Effective force (P) = 180KN Eccentricity (e) = 50mm…

Q: The beam is fabricated from two equivalent structural tees and two plates. Each plate has a height…

Q: 6 kN/m 3 m

Q: The observed bearings of a traverse are given below. Line Bearing PQ 46° 15' QR 108° 15' 201° 30' ST…

A: Given data :- Line Bearing Line Bearing PQ 46°15' QP 226°15' QR 108°15' RQ 286°15'…

Q: Determine the energy loss due to a sudden enlargement from a standard DN 25 Schedule 80 steel pipe…

A: Data given Q = 3×10-3 m3/s Find : Head loss due to sudden enlargement

Q: E= 29000ksi 1=291 in4 6 ft ↓↓↓ B Determine the deflection of the beam at midspan. Answer in inches…

Q: Determine the cracking moment in kip-ft for the section shown if: f'c = 4000psi and f₁=7.5√f'c. 9…

A: Given:- The compressive strength of the concrete = 4000 psi The steel reinforcement provided = 3-#10…

Q: A flanged bolt coupling has ten 16-mm diameter steel bolts on 800 mm diameter bolt circle a nd six…

A: Given: Ten 16 mm diameter steel bolts on 800 mm diameter bolt circle Six 20 mm diameter steel bolts…

Q: Find the critical depth in the triangular channel. Velocity = 2.5m/s depth= 1.8m side slopes…

A: Given Data Velocity of flow (V) = 2.5 m/s Depth of flow (y) = 1.8 m Side slope (1:m) = 1:2 Find…

Q: Question No. In an aquifer extending over 150 hectare, the water table was 20 m below ground level.…

A: Given data- An aquifer- Area A=150 ha, Initial depth of water table from ground level=20 m, Final…

Q: Beams and Slabs Question 7 acol dom A reinforced concrete beam, supported on columns at ends, has a…

A: Given- Clear span=5 m Effective depth = 0.5 m UDL=100 kN/m It is needed to find the design shear…

Q: Assume a constant value of EI = 560×10° N-mm² for the beam. A 210 N-m 200 mm Determine the…

Q: Solve the following problems and write your complete solution. 1. A nylon string has a diameter of 2…

A: Given that:- Force = F = 100N Diameter = d = 2 mm To determine the normal stress

Q: In a soil investigation work at a site, Standard Penetration Test (SPT) was conducted at every 1.5 m…

A: Given SPT test data Number of blows at 150 mm successive penetrations- 8, 6 & 9.

Q: Please resolve this problem. Solve in 3 decimal places. Check if the solutions are correct. THUMBS…

Q: A company that manufactures pulse Doppler insertion flow meters uses the Straight Line method for…

A: Given: First cost = $120000 Salvage value = $16500 Life = 3year Required : Depreciation charge and…

Q: 10 m E-300 GPa 30 kN/m -10 m Ela contam -10 m 7-700 (10) m (a) Indeterminate Beam

Q: What are the five steps of a preliminary investigation?

A: Preliminary investigation- Gathering information about the type of structure to be built and its…

Q: Calculate the friction drag on a plate 0.15 m wide and 0.45 m long placed longitudinally in a stream…

Q: Over a basin of area 300 km², there was a storm for 4 h with a uniform intensity of 4 cm/h. The…

A: Given Area A=300 km2 time t= 4hrs Intensity I=4 cm/h Runoff R= 40×106 m3

Q: A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm…

A: Given data- A double cover butt riveted joint- Two flat plates of 200 mm width, b=200 mm, Thickness…

Q: Traffic flow on a three-lane (one direction) freeway can be described by the Greenshields model. One…

A: Given:- The number of lanes = 3 One lane is closed for an emergency bridge repair for 2 hours The…

Q: A steel beam is subjected to a maximum shear force of 80 kN. The cross-section of the beam is shown…

A: Given Data Maximum Shear force (V) = 80 KN Find 1. Shear stress at neutral axis. 2. Shear stress…

Q: QB.41. A square tied column with a side dimension of 575 mm is reinforced with 12-30 mm dia. bars…

A: Answer Calculation of relative stiffness(EI) Since the column and bar size is already been selected…

Q: E= 29000ksi 1=291 in4 6 ft B Determine the deflection of the beam at midspan. Answer in inches…

Q: For accident statistics in table below. Comput the following: a) Rates of fatality depending on…

A: Accident statistics are given in the above table. We have to find out: 1. Fatality rate depending…

Q: Determine the overall column length that, if exceeded, would cause the column to buckle elastically…

A: Answer To calculate the overall column length which causes the column to buckle elastically before…

Q: The following data pertains to the number of commercial vehicles per day for the design of a…

Q: Question 5: For system shown below, estimate: 1. The head, flow rate, and efficiency in case of…

A: Given, Pump curves for certain flow system

Q: 21 The volume coefficient of thermal expans ion is equal to two times the value of area coefficient…

Q: 20 KN B 6 m 12 m 15 KN to 2 kN/m 30 m 18 m D 8 m 30 KN E

Q: -19. The piece of plastic is originally rectangular. Determine the shear strain Y., at corners D and…

A: Find: Shear strain at D and C

Q: Cebu City. Concrete piles will be used as its foundation with details and plans as follows: TT 38…

A: Data provided : detail foundation plan concrete piles = 450 x450 mm six number of identical footing…

Q: Calculate the friction drag on a plate 0.15 m wide and 0.45 m long placed longitudinally in a stream…

Q: 2. For the following figure shown, determine the radius of gyration. 2 cm 4 cm N 4 cm 2 cm 2.5 cm 1…

A: Given, Cross section of member To find : Radius of gyration

Q: Need 1 m3 of 35 N/mm2concrete (specified compressivestrength). From testing a representative sample…

A: Given: Quantity of fine aggregate needed = 477 kg in dry condition Total moisture of fine aggregate…

Q: Question No. 22 The ordinates of a 2-h unit hydrograph at I hour intervals starting from time t = 0,…

A: Given- Total rainfall P=6.6 cm Duration of rainfall D=3 h ϕ-index=2 mm/h=0.2 cm/h Base flow B=5 m3/s…

Q: A +0.7% grade meets a -0.4% grade at sta 2+700 and at elevation 30 m. The max allowable change in…

A: Given information, n1 = 0.7% n2 = -0. 4% Maximum allowable change in grade/sta.=0.2%

Q: beam with hinge support on one end and a fixed support on the other end has _________ redundant…

Q: What is causing the shift to large cities? Why are vertical cities emerging as a new urban form?…

A: The migration to major cities is being driven largely by two factors: the rise in population and the…

Q: A steel platein. thick is embedded in a concrete wall to anchor a high-strength cable as shown. The…

Q: Sketch SFD and BMD in terms of w and P

Q: a. The reactions at the support for a simple beam loaded as shown. Neglect the weight of the beam.…

Question

100%

Strength of Materials (Upvote will be given. Please write the complete solutions and FBDs Legibly. No long explanation needed. Solve in 3 decimal places.)

30
If the total
deformation of the compo
site rod in the figure is limited to 0.90
mm, compute the maximum value of
"P" that is safe for the composite rod.
3P
BRONZE
A = 450 mm²
L = 0.6 m
E = 83 GPa
P
ALUMINUM
A = 600 mm²
L = 1.0 m
E = 70 GPa
4P
STEEL
A = 300 mm²
L = 0.8 m
E = 200 GPa
2P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the x-bar centroid of the composite figure shown. Where: x=4 ft
10/10 FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70 kN/MM2 100 kN RALU=30 MM Aluminum Steel 1m R ST 20 MM
Determine the y-bar centroid of the composite figure shown. Where: x=4 ft 2 A 1 ft 1ft
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 0.02 in. - 14 in. 18 in. Aluminum A = 2.8 in? E = 10.6 X 106 psi Bronze A = 2.4 in? E = 15 x 106 psi a = 12 x 10-6/°F a = 12.9 x 10 /°F Determine the temperature at which the normal stress in the aluminum rod will be equal to -7 ksi. The temperature of the aluminum rod is |°F.
A composite beam is made of two brass (E =110GPa) to two aluminum bars (E = 70GPa), as shown. The beam is subjected to a bending moment of 380 N-m acting about the z-axis. Using a = 5mm, b = 40mm, c = 10mm, and d = 25mm. Calculate: a) the maximum bending stress in the aluminum bars b) the maximum bending stress in the brass bars
The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P 52 kips is applied at 65° F. Compute the stress (ksi) in the Aluminum at 116 °F. Assume a = 6.5 x 106/° F for steel and 12.8 x 106°F for aluminum Given: L1 = 17in; L2 = 13in %3D %3D Your final answer should contain two decimal places Aluminum A = 2 in? E = 10 x 10 psi Steel A = 3 in? E = 29 x 10 psi L1 - L2
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Steel Eg = 200 GPa Acp= 39 mm? Aluminum Соpper Eg = 70 GPa AAB= 58 mm? Ecu = 126 GPa ABc = 77 mm? 16 kN 8 kN 9 kN 7 kN 16 kN 8 kN – 450 mm- -300 mm- 400 mm-
For the composite area shown in Figure 4.1c, determine the y-coordinate of its centroid. Given B1 = 90 mm, Br2 = 108 mm, D = 120 mm, t1 = 48 mm, t2 = 24 mm and tw = 18 mm. The positive x and y axes of the coordination system are shown in the figure. Ba – ½D tw D ½D t2 B2 -
The composite bar is firmly attached to unyielding supports. Compute the stress (psi) in each material caused by the application of the axial load P = 50 kips Aluminum A = 1.25 in? E = 10 x 10° psi Steel A = 2.0 in? E = 29 x 10° psi 15 in 10 in
! Required information A steel bar (Es= 210 GPa) and an aluminum bar (Ea = 70 GPa) are bonded together to form the composite bar shown. 8 mm 8 mm 8 mm Aluminum 24 mm -Steel Determine the maximum stress in steel when the bar is bent about a horizontal axis, with M= 56 N.m. The maximum stress in steel is - MPa.