30 mm 40 mm

Q: The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is subjected to the…

A: The diameter of the shaft is d = 40 mm. The couple acting on the shaft is F = 3 kN. The length of…

Q: 7-54. The lever is attached to the shaft A using a key that has a width d and length of 25 mm. If…

A: The width of the key is d. The length of the key is l =25 mm =0.025 m. The vertical force acting on…

Q: If P = 14 kN determine the average shear stress developed in the pins at A, B, and C. All pins are…

A:

Q: F14-L Determine the normal stress and shear stress acting on the Inclined plane AB.

A: The normal stress acting on the vertical plane is σ1=500 kPa. The inclination of the plane AB from…

Q: The A-36 steel pipe has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN.…

A: Given data as per question Tensile force = 200 KN Outer diameter = 80 mm Inner diameter = 70 mm…

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: F7-15. Determine the maximum average shear stress developed in each 12-mm-diameter bolt. 10 kN 5 kN…

A: Given that →Load=10 KN                    dia=12 mm=0.012 m

Q: The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in the…

A: Given data as per the question  diameter of shaft = 50 mm

Q: Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free…

A:

Q: If the joint is subjected to an axial force of P = 9 kN, determine the average shear stress…

A: Given Applied load = 9 kN Diameter of bolts = 6 mm To find Average shear stress in each bolts…

Q: The A-36 steel tubular shaft is 2 m long and has an outer diameter of 50 mm. When it is rotating at…

A: Given data as per question Length of tubular shaft = 2 m Outer diameter = 50 mm Power transmission =…

Q: The bar has a constant width of 35 mm and a thickness of 10 mm. Determine the maximum average normal…

A:

Q: The overhang beam is subjected to the uniform distributed load having an intensity of w = 50…

A: The maximum shear force acting in the span AB is 150 KN

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: The solid aluminum shaft has a diameter of 50 mm and allowable shear stress of tallow = 60 MPa.…

A:

Q: Determine the maximum average shear stress developed in the 30-mm-diameter pin.

A: Given Data: The diameter of pin is d = 30 mm. Force in x-direction is Fx = 40 kN. Force in…

Q: The plastic hexagonal tube is subjected to a torque of 150 N # m. Determine the mean dimension a of…

A: Given: The torque on a plastic hexagonal tube is T=150 N-m. The allowable shear stress on a plastic…

Q: If P = 15 kN, determine the average shear stress in the pins at A, B, and C. All pins are in double…

A: Given: The value of load, P = 15 kN The diameter of pin, d = 18 mm = 0.018 m   The free body diagram…

Q: F7-2 F7-A Determine the absolute maximum shear stress developed in the beam. 3kip 1 F-3

A:

Q: The shaft consists of a solid segment AB and a hollow segment BC, which are rigidly joined by the…

A: Given for solid part D=80 mm Cs=80/2=40mm Max. shear stress for solid rod is given…

Q: Determine the normal stress and shear stress acting on the inclined plane AB. Sketch the result on…

A: Given figure, The normal stress in x direction is €x=500 kpa  Shear stress Txy=0,

Q: *10-4 The link acts as part of the elevator control for a small airplane. If the attached aluminum…

A: Given Data: Applied force is F = 600 N. Distance between the forces is r = 75 mm + 75 mm =150 mm.…

Q: The 6-hp reducer motor can turn at 1200 rev>min. If the shaft has a diameter of 5 8 in.,…

A: Given: The power of the reducer motor is P=6 hp. The angular velocity of the reducer motor is ω=1200…

Q: The solid circular shaft is subjected to an internal torque of T = 5 kN # m. Determine the shear…

A:

Q: The solid steel shaft AC has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Given data The diameter of the shaft, d = 25 mm. The rotation speed of the shaft, N = 50 rev/s.…

Q: F7-8. Determine the average normal stress on the cross section. Sketch the normal stress…

A: Given Applied load = 300 kN Inner radius = 80 mm Outer radius = 100 mm To find Sketch normal stress…

Q: The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A: force=8 kN (a) average normal stress in the shank                          σs=PA=…

Q: 2. The shaft is hollow from A to B and solid from B to C. (a) Determine the maximum shear stress…

A:

Q: Q-1 Two wrenches are used to tighten the pipe. If P = 350 N is applied to each wrench, determine the…

A:

Q: A torque of 2 kip # in. is applied to the tube. If the wall thickness is 0.1 in., determine the…

A: Torque T = 2 kip in = 0.16 kip ft thickness t = 0.1 in rm = (2 + 1.9)/2  in =1.95 in Am = π4 rm2=…

Q: 30° •1-61. Determine the maximum magnitude P of the load the beam will support if the average shear…

A:

Q: The gear motor can develop 14 hp when it turns at 600 rev>min. If the shaft has a diameter of 12…

A: Given Data: The power developed by the motor is P = 14 hp. The number of revolutions is N = 600…

Q: Determine the shear stress at point A on the surface of the shaft. Represent the state of stress on…

A: Write the twisting moment at the cross section containing point A.

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Find the absolute maximum shear stress

Q: The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It is…

A: According to the given condition  We have the stress along its longitude as…

Q: F7-18. Determine the maximum average shear stress developed in the 30-mm-diameter pin. 30 kN 40 kN

A: Given data: The diameter of pin, dpin = 30 mm. Calculate the resultant force as follows: R=30…

Q: Determine the maximum shear stress in the strut if it is subjected to a shear force of V = 20 kN.

A: Given data V=20 KN

Q: If the shaft is subjected to a uniform distributed torque of t = 20 kN # m>m, determine the…

A: Given data t=20 kN·m/m

Q: The three suspender bars are made of A-36 steel and have equal cross-sectional areas of 450 mm2…

A:

Q: The plastic tube is subjected to a torque of 150 N # m. Determine the average shear stress in the…

A: Torque=150 N-m =150×103 N-mm ; mean dimension (a) =200 mm ; thickness (t)=3 mm ;…

Q: QI/If the beam is subjected to a shear force of V= 80 kN, determine the shear stress developed at…

A:

Q: The thin-walled pipe has an inner diameter of 1.2 cm and a thickness of 0.06 cm. If it is subjected…

A: Determine the axial and hoop tension as follows.

Q: F9-1. Determine the normal stress and shear stress acting on the inclined plane AB. Sketch the…

A: Given:-σ=500 kPaθ=30°To find:-Normal stress Shear stress

Q: The shaft is made of red brass C83400 and has an elliptical cross section. If it is subjected to the…

A: The Torsion formulae in case of shafts with elliptical section gets modified  and are as mentioned…

Q: If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress…

A:

Q: The L2 steel blade of the band saw wraps around the pulley having a radius of 12 in. Determine the…

A: Given data: The radius of curvature of the pulley, ρ = 12 in. Width of the blade, w = 0.75 in. The…

Q: The steel step shaft has allowable shear stress of tallow = 8 MPa. If the transition between the…

A: Given data: Allowable shear stress, τallow = 8 MPa. Diameter of the larger cross-section, D = 50…

Q: The hollow circular shaft is subjected to an internal torque of T = 1 0 kN # m. Determine the shear…

A: Given,Torque(T)=10 KN-m=107 N=mmBy torsion equation:→TJ=τRWhere,J=Polar moment of…

Q: 12-7. The shaft is supported by a thrust bearing at A and a journal bearing at B. IF P = 20 kN,…

A: Given data as per the question Force, P=20 KN