300 mm B 600 mm 400 N·m 600 mm 200 N·m 800 N-m The 50-mm-diameter A992 steel shaft is subjected to the torques shown. Determine the angle of twist of the end A. - change the steel shaft from a solid cross-section into a tubular cross-section - keep the outside diameter = 50 mm and the inside diameter = 35.5 mm

300 mm B 600 mm 400 N·m 600 mm 200 N·m 800 N-m The 50-mm-diameter A992 steel shaft is subjected to the torques shown. Determine the angle of twist of the end A. - change the steel shaft from a solid cross-section into a tubular cross-section - keep the outside diameter = 50 mm and the inside diameter = 35.5 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid shaft made of steel [G = 80 GPa] is subjected to the torques shown. Determine theangle of twist along the shaft measured at gears B, C, D, and E relative to the flange A. Diameter of the shaft is d= 20mm. [TB = 25 N.m; TC = 35 N.m; TD = 24 N.m; TE = 14 N.m][dABCDE = 20 mm (diameter); LAB = 300 mm; LBC = 400 mm; LCD = 400 mm; LDE = 250 mm]
A circular shaft of the dimensions shown in the following figure is subjected to three torques : T1= 28 k-in, T2= -8 k-in and T3 = 10 k-in. (a) What is the angle of twist of the right end due to the applied torque? (b) Plot the angle of twist diagram along the shaft. Let, G= 12×10^6 psi.
The beam section given in the figure is under the influence of M = 5 kN.m bending moment. Momentin topassuming that pressure is exerted on the head, the normalCalculate the stresses. E = 200 GPa.
A brass disk of radius 0.7 ftft and weight 459 lblb sits in a right-angle groove made of granite. The disk makes contact with the groove at AA and BB and the coefficient of static friction at both points are μS=μS= 0.39 A couple moment of MM is applied to the disk as shown.
In the figure, the rigid AD bar is held vertically by two elastic rods articulated at the ends, which are horizontal at points B and C. Under the effect of a horizontal load of 120 kN of the system; a) Calculate the forces to occur in the elastic bars, b) The displacement of the top point (A) of the rigid bar. Note: (EA = 108N)
PLEASE REFER TO THE GIVEN VALUES BELOW. For the beam loaded as shown in the figure, determine the following unknowns using DOUBLE INTEGRATION METHOD. Consider 300 mm x 300 mm section and E = 200 GPa. Round-off to 3 decimal places. a = 3.3m b = 16 kN/m c = 16 kN - Determine reaction at A in kN. - Slope of the elastic curve at A in degrees. Indicate negative sign as necessary. - Deflection at B in mm. Indicate negative if downward. - Deflection at D in mm. Indicate negative if downward.
The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block A. The cutting angle is 30.296 degrees. Neglect friction. Computations must observe D`Alembert's Principle. a) Determine the normal force of contact between block A and block B. Express answer in Newtons or KiloNewtons.b) Determine the acceleration of block A. Express answer in meters per seconds.c) Determine the acceleration of block B. Express answer in meters per seconds.
Solve the equation 2y dx = 3x dy..
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; / = 1930 in.41. For the loading shown, determine: (a) the beam deflection at point A (b) the beam deflection at point B. Assume MA = 250 kip-ft, P = 29 kips, LAB = 4.9 ft, LBc = 7.4 ft.
the clamp exerts a normal force of 100N on the three pieces held together as shown. what force P may be exerted motion impends? the coefficient of friction between the pieces is .60
A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1850 in.4]. For the loading shown, determine:(a) the beam deflection at point A.(b) the beam deflection at point B.Assume MA = 180 kip·ft, P = 25 kips, LAB = 7.3 ft, LBC = 11 ft.