4-38. A) For the concurrent force system shown, calculate the maximum load W that could be supported if the maximum allowable force in each cable were 1200 lb. Please show work 12 5 عامل 45° W Jo 3 B) Calculate the force in each cable for the suspended weight shown. Please show work Y K W 500 lb 6'-0" 30⁰° 12'-0"

4-38. A) For the concurrent force system shown, calculate the maximum load W that could be supported if the maximum allowable force in each cable were 1200 lb. Please show work 12 5 عامل 45° W Jo 3 B) Calculate the force in each cable for the suspended weight shown. Please show work Y K W 500 lb 6'-0" 30⁰° 12'-0"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.67-in .-diameter pin at A, and the 0.43-in .-diameter cable BC. Neglecting the weight of the boom, determine the tensile stress in the cable (in psi) if P = 4589 lb. Round off the final answer to three decimal places.
Compute all reactions at the base A of the traffic light standard, given that the tension inthe cable BC is T = 544 lb. The weight of the standard is negligible compared with the 320-lb weight ofthe traffic light. Please show complete solution.
A cable is supported at points A and B which are 250m horizontally apart and with point B 20m below point A. The cable is loaded by 4 kN/m along the horizontal and its slope at point B is equal to zero. Find the tension at the points of supports. ANS.TA = 6329.5 kNTB = 6250 kN
The spike shown needs to be removed horizontally but an obstruction at A prevents direct access. Thus, 2 cables are provided with their lines of action shown as forces P and 1.6kN. Determine force P to ensure that the resultant R is directed along the spike. Also, compute the resultant. Show solution where answer is P = 2.15 kN & R = 3.2 kN
The cable is subjected to tensile force of 13 kN. Calculatethe internal normal force, shear force, and moment at thecross section through point C. What will be the safe valueof P? The radius of the pulley is 0.1 m
Compute for the cable forces acting on the tower shown. use height of tower = 50m
A precast-concrete wall section is temporarily held by the cables shown. Knowing that the tension is 840 lb in cable AB and 1200 lb in cable AC. Determine the magnitude and direction of the resultant of the forces exerted by cable AB and AC on stake A. (R, θx, θy, and θz)
Replace the concurrent cable forces acting on the plate shown by a single resultant force R. Also, find the coordinates of the point where R intersects the plate. Express R in rectangular form.
Compute for the cable forces acting on the tower shown. Height of tower is 60m.
Help me asap Two poles are 100m away from each other. The difference in elevation of the top of the poles is 10m. A parabolic cable connects them such that the vertical distance of the lowest part of the cable is 5m from the top of the lower pole. If the minimum tension in the cable is 200kN. Find: A. Determine the force of the cable on the lower pole (kN) B. Determine the force of the cable on the higher pole (kN) C. Determine the horizontal distance between lowest part of the cable and the lower pole (m) D. Determine the tension 20m from the higher pole (kN)
The cable supports the three loads shown.Determine the sags yB and yD of B and D. Take P1 = 800 N, P2 = 500 N.
Determine the total length of cable, If y=20m. a.) 177.809 KN b.) 176.089 KN c.) 175.980 KN d.) None of the above e.) 178.908 KN