4-49. Determine the angle o at which the applied force P should act on the pipe so that the magnitude of P is as small as possible for pulling the pipe up the incline. What is the corresponding value of P? The pipe weighs W and the slope a is known. Express the answer in terms of the angle of kinetic friction, = tan H-

4-49. Determine the angle o at which the applied force P should act on the pipe so that the magnitude of P is as small as possible for pulling the pipe up the incline. What is the corresponding value of P? The pipe weighs W and the slope a is known. Express the answer in terms of the angle of kinetic friction, = tan H-

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.89RP: The woman is trying to move the crate of weight W by pulling on the rope at the angle to the...

See similar textbooks

Similar questions

Determine the smallest force the man must exerton the rope in order to move the 80-kg crate Also,what is the angle θ at this moment? Thecoefficient of static friction between the crate andthe floor is μs = 0.3.
Find the minimum force P required for impending motion of the block up the inclined surface, given: Mblock = 65 kg, θ = 52 °, μ = 0.4
The 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.
5-31. If the force of the smooth roller at B on the bar bender is required to be 1.5 kip, determine the horizontal and vertical components of reaction at pin A and the required magnitude of force F applied to the handle.
The three bars have a weight of WA = 20 lb, WB =40 lb, and WC = 60 lb, respectively. If the coefficientsof static friction at the surfaces of contact are asshown, determine the smallest horizontal force Pneeded to move block A.
The 3600-lb car with rear wheel drive is attempting to push the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide. (The car pulling the crate is analyzed in Prob. 7.19.)
3. Determine whether the 10 kg block shown is in equilibrium, and find the magnitude and direction of the friction force when P = 40 N and 0 = 20⁰. μ = 0.30 M = 0.25 20°
Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components ofreaction at the journal bearing C and thrust bearing D if θ = 0°. The bearings are in proper alignment and exert only force reactions on the shaft.
in the pulley system and the diagram above, assume that the bearings at oh and C are properly aligned and smooth and that T2 =30 N all dimensions in millimeters and the belt tensions are all tangential to the pulleys a. If the shaft runs at a constant speed, determine the tension T1 b draw a free body diagram of the shaft and determine the reactions at bearing sea in terms of the components along the Y and Z axis. Assume neither bearing and oh or see produces an axial thrust
Find the force P required to pull the 40-kg homogeneous roller with radius 720mm over the 90-mm curb.
The woman is trying to move the crate of weight W by pulling on the rope at the angle to the horizontal. Find the smallest possible tension that would cause the crate to slide and the corresponding angle .
The 449-N force is applied to the 81-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left.