4: Design a buck converter to produce an output voltage of 18 V across a 10-_ load resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.

4: Design a buck converter to produce an output voltage of 18 V across a 10-_ load resistor. The output voltage ripple must not exceed 0.5 percent. The dc supply is 48 V. Design for continuous inductor current. Specify the duty ratio, the switching frequency, the values of the inductor and capacitor, the peak voltage rating of each device, and the rms current in the inductor and capacitor. Assume ideal components.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
Two SCRs are used in a midpoint converter arrangement. The source RMS voltage is230 V, and the frequency is 50 Hz. The load is 100 mH inductor in series with 2 .The input lines have series inductance 50 H. (a) For a phase delay of 45, plot the voltage waveform measured at the output of the midpoint converter. (b) What is the output power for 45 delay?
For a single-phase Ac-Ac Converter with unidirictional phase control, find the output dc voltage, where, the delay angle is 0 degree, the input voltage is 120sinwt with 10ohm resistive load consider
in steady state Operation of Boost DC-DC Converter , Identify the component in the converter, which exhibits the highest power loss. Provide a proper reason for your answer. What is the duty ratio (D) How can it effects on the converter output (Vo) Explain the relation between the output power and system efficiency. What is the maximum voltage occurs across the switch in your practical results? Is there any difference between practical and theoretical results? Comment. 5. Compare between control characteristics of the buck and boost converters
Q.) The circuit shown below is an idealized forward converter. Assuming an input voltage Vd=40V, duty cycle of 0.5 and an output power of 50W with a resistive load of 50Ω. What is the transformer ratio, N1:N2 of this converter ?
plot the theoretical and practical control characteristics of the Buck converter, and comments on your the obtained curve.
1.Design a buck converter and a resistive load operating in CCM mode with the following specifications:(∆V0)/V0= 0.5 %, Vin = 20 V, f =30 kHz, Duty cycle d=0.4, and R =5.33 Ω. Determine (a) the output voltage and current of the buck converter, the Critical(minimum) inductance for CCM mode (b) select L = 600 µH, find the maximum IL,max and the minimum IL,min inductorcurrents. find the capacitor value that corresponds to (∆V0)/V0= 0.5 % for this buck converter
1) The current and voltage waveforms given in the figure on the right.power electronics converter to which the shapes belongDraw the circuit. The stress on the load andThe relations for the average value of the current are obtained.please. 2) Positive half wave of AA voltage transferred to the loadfixed negative half wave is a controllableDraw an AA phase control circuit. Pure ohmic load and ?output current and voltage for a trigger angle such asGive the waveforms. 0 <? <pi
Design of Bidirectional DC-DC Boost Converter. explain its working principle and plot its input - output graphs.
A load resistor RL is in parallel with a noisy source (vS << VS), and a biasing component, which canbe a linear or a nonlinear element. Suppose we can write the total source voltage vS and the totalload voltage vL as shown in the image. Answer the ff and explain clearly. i. Let the biasing component be a linear resistor with resistance RB. Without the noise, determinethe value of RB so that the load voltage is 5V. ii. With the noise, determine the ratio of the load voltage noise and the source noise (vI /vS )..
Draw the circuit diagram of a Transformer Coupled Push Pull Amplifier. Explain its working taking a sinusoidal signal as the input.
The circuit shown below is an idealized forward converter. Assuming an input voltage Va=40V, duty cycle of 0.5 and an output power of 50W with a resistive load of 50ohm. What is the transformer ratio, N1:N2 of this converter ?