4) Take that W,= 3.8 kN/m intensity for the distributed load below. The fixed support at O can have support reactions with a vertical and horizontal force and a moment. B) Answers: A) Show your free body diagram with the resultant loads, their locations and indicate the support reactions. Mo= Ox= -3m- Oy= Wo -1.5 m- What are the support reactions at the fixed support at O?

4) Take that W,= 3.8 kN/m intensity for the distributed load below. The fixed support at O can have support reactions with a vertical and horizontal force and a moment. B) Answers: A) Show your free body diagram with the resultant loads, their locations and indicate the support reactions. Mo= Ox= -3m- Oy= Wo -1.5 m- What are the support reactions at the fixed support at O?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.26P: A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E....

See similar textbooks

Similar questions

A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
As shown in figure below, the intensity of loading on a simply supported beam10 ft long is given by ? = 10?3 where y in in lb/ft and x is in ft measured from A.Find the reactions at A and B.
Q/ Find the reaction forces at A and B, (A pin connection and B roller connection)? 120N/m
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
The triangular block shown in the figure is subjected to the loads P = 1600 lb. and F = 600 lb. If AB = 8 in and BC = 6 in., resolve each load into components normal and tangential to AC.
Question 1) in FIG loading condition is given beam F force F = 65 kN , first distributed load W 1 = 41 kN / m , w 2 distributed load w 2 = 51 kN / m , θ angle θ = 48 ° and L length of L = 5 m . According to this; Question 1-A) B at the point y direction ( B y ) Determine the support reactions. (Enter yourresultwithout writing kN units.) Question 1-B) to the point in y direction ( A y ) Determine the support reactions. ( Enter yourresult without writing kN units.) Question 1-C) to the point in x direction ( A x ) Determine the support reactions. ( Enter yourresult without writing kN units.)
The figure above shows a free-standing beam with a point load. Determine the bearing forces in A and B. Ax = Az = Bx = Bz =
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where Mo = 14,688 lb-in, Wo = 750 lb/ft, a = 12 ft, b = 4 ft, c = 7 ft.
The total axial load acting at the centroid at on the leftmost rib would be 2F2 and the total axial load acting at the centroid at section C would be 2F3 A) Assume that the axial member is in equilibrium and the applied forces are an unknown load F1, F2 = 11 kN , F3 = 9 kN , and F4 = 6 kN . Calculate the internal resultant normal force at section B. B) Calculate the internal resultant normal force at section D. C)Suppose the axial member has a circular cross section with a diameter of dB = 16 cm at section B and a diameter of dD = 8 cm at section D. What is the average normal stress in the section with the maximum magnitude stress?
When a beam has only uniformly distributed forces applied, the moment diagram consists of piecewise (answer) forces.
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where M0 = 1,220 N-m, P = 2650 N, F = 3000 N, w0 = 1702 N/m, w1 = 1103 N/m, a = 3 m, b = 6 m, c = 2 m