(4) The A-36-steel band, made up of two halves, is 50 mm wide and is secured around the smooth rigid cylinder. If the bolts are tightened so that the tension in them is 2 kN, determine the normal stress in the band, the pressure exerted on the cylinder, and the amount of stretch that occurs in each half the band. 5 mm 200 mm

(4) The A-36-steel band, made up of two halves, is 50 mm wide and is secured around the smooth rigid cylinder. If the bolts are tightened so that the tension in them is 2 kN, determine the normal stress in the band, the pressure exerted on the cylinder, and the amount of stretch that occurs in each half the band. 5 mm 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm
4-82. The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T₁ = 15°C. If the two 304 stainless steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 12 MPa. 100 mm Probs. 4-81/82 150 mm
A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kN including its self-weight which is distributed equally:a. Determine the stress on the lower washers before the buts are tightened. b. Determine the stress in the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt.c. Determine the stress in the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. Show the FBD.
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F
For the clevis connection shown, determine the shear stress in the 23-mm-diameter bolt for an applied load of P = 165 kN. O 141 MPa O 211 MPa O 167 MPa O 120 MPa O 199 MPa Clevis
A flexural member is fabricated from two flange plates 1/2x16 and a web plate 1/4x20, thusforming a built-up ‘I’ shape member. The yield stress of the steel is 50 ksi.a. Compute the plastic section modulus Z and the plastic moment Mp with respect to the majoraxis.b. Compute the section modulus S and the plastic moment My with respect to the major axis
The bolted connection is subjected to a tensile force of P. The diameter of the bolt is d=60 mm. if P=200kPa. Determine the average shear stress (MPa) in the bolt.
For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
4-82. The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T1 = 15°C. If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 12 MPa. 100 mm 150 mm Probs. 4-81/82
A brass sleeve S is fitted over a steel bolt B, and the nut is tightened until it is just snug. The bolt has a diameter of dB = 25 mm, and the sleeve has inside and outside diameters of d1 = 26 mm and d2 = 36 mm, respectively. d2 di dB Sleeve (S) Bolt (B) Calculate the temperature rise AT that is required to produce a compressive stress of 23 MPa in the sleeve. (Use material properties as follows: for the sleeve, as = 21 x 10-6/C and Es = 200 GPa; for the bolt, aB = 10 × 10¬6/°C and EB = 400 GPa.) AT = °C (Round to the nearest whole number.)
A brass sleeve S is fitted over a steel bolt B, and the nut is tightened until it is just snug. The bolt has a diameter of dg = 25 mm. and the sleeve has inside and outside diameters of di = 26 mm and dz = 36 mm, respectively. d2 di Sleeve (S), dB Bolt (B) Calculate the temperature rise AT that is required to produce a compressive stress of 24 MPa in the sleeve. (Use material properties as follows: for the sleeve, as = 21 x 10-6/°C and Es = 200 GPa; for the bolt, aB = 10 x 10-6/*C and Eg = 400 GPa.) AT = *C (Round to the nearest whole number.)
4 A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six 16 mm diameter aluminu m bolts on 300 mm diameter bolt circle. T he maximum shear stresses of the materi als are 60 MPa in steel and 40 MPa in al uminum. Use G = 80 GPa for steel and 3 0 GPa for aluminum. What is the maximu m required shear strength of each alumin um bolt to determine the maximum torqu e that can be applied to the system? Dra wing not included in this problem.