4. Doors Lite is called rail door? 5. Composite beams are constructed from steel and timber? 6. The set of sills with a section of iron, which bears high loads, is called Girder? 7. Granite is used to cover bathroom floors? 8. PVC is used for basement and garage floors? 9. In one-way slab there is main reinforcement in two directions? 10. shell roof is relatively thin and does not require support beams?

4. Doors Lite is called rail door? 5. Composite beams are constructed from steel and timber? 6. The set of sills with a section of iron, which bears high loads, is called Girder? 7. Granite is used to cover bathroom floors? 8. PVC is used for basement and garage floors? 9. In one-way slab there is main reinforcement in two directions? 10. shell roof is relatively thin and does not require support beams?

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter28: Structural Components Of Framed Construction

Section: Chapter Questions

Problem 28.10Q

See similar textbooks

Similar questions

design of concrete beam
As a design engineer you are asked to peer review the design done by another engineer at your organization. A typical reinforced concrete floor slab plan is given. Assume all members to be simply supported. The specified compressive strength of concrete is 5000 psi and Grade-60 steel is used. Unit weight of concrete can be assumed as 150 lb/ft³. B 30'-0"- B2 -EQ.- EQ. -EQ. SEC 1 -40'-0" IS B1 B3 B3 B1 2 The only dead load acting on the slab is the self-weight of the members. The live load on the slab is 100 psf. Initial cross-section and reinforcement details of beam B1 is shown. Area of steel is 4.8in². EQ. 40'-0" B EQ. North
6. ESTIMATION OF QUANTITIES OF STEEL & R.C.C. ELEMENTS EPU Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars are 10mm@400mm c/c. All offset bars 12mm@400mm c/c, All Additional Top bars 12mm@400mm c/c. The slab thickness is 150mm. Assume cover is 25mm & wall thickness20cm 0.45 0.45 3.70 4.70 0.45 0.45 3.70 5.20 3.10 1.60 150
Concrete ped.
Design of Concrete Beams
Reinforced concrete-Explain with the diagram
3. List and discuss the five main types of defects in timber.
two span beam subjected to shear and flexure only is reinforced as follows: Section @ midspan @ face supports Top bars 2-20mm 5-20mm Bottom bars 3-20mm 2-20mm Given Stirrup diameter: 10 mm concrete fc = 21 mpa steel rebar fy = 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in single layer calculate the following: a) tensile steel ratio in positive bending moment at midspan (round off to 5 decimals) b) design moment strength of section at midspan for positive bending ( in kN•m , nearest whole number) c) nominal design strength of section at face of support for negative bending ( in kN•m , nearest whole number)
Introduction Concrete encased steel composite beam
Q#1: Differentiate between the following: One way beam supported Slab & One way Joist Slab Subject: RCD 2
Concrete Technical / Practical Part.
+ „blackboard.com/ultra/courses/_96287_1/cl/outline Question Completion Status: 4 8 9 10 A two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @ FACE OF SUPPORTS TOP BARS 2-020 mm 5-Ø20 mm BOTTOM BARS 3-020 mm 2-020 mm Given: Stirrup diameter, ds = 10 mm Concrete fc = 21 MPa Steel rebar = 415 MPa Stirrup fy = 275 MPa %3D Beam size b xh = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: Tensile steel ratio in positive bending at midspan = (in 5 decimal places) kN m (nearest whole Design Moment strength of section at midspan for positive bending = 32°C Light rain ^ O O G ) ENG 1:42 pm ロ