Please answer with solution, and brief explanation, thank you. 4. Forces P and F acting along the bars shown maintain equilibrium of pin A. Determinethe values of P and F.Ans. P = 14.76 KN (C), F = 39 KN (T)4 m3 m2 m18 KN30 kN 5. Determine the pin reactions at A and all forces actingon member DEF of the frame shown. Neglect theweights of the members.Ans. A = 60 KN, F = 28.30KN6. Two cables are tied together at C and loaded asshown. Determine the tension in cable AC and BC.Ans. AC = 2.5 KN (T), BC = 2.72KN (T)B3.4 mLa4.8 mT с2m1.98 kN3 m3.6 m1 m40 kN-2 mB1 mA2.5 m2.5 m-xDF60°F0.5 mE1 m3 m

Answered: Image /qna-images/answer/8667fb11-78e1-4627-9155-f93662e92dc4.jpg

Answered: 4. Forces P and F acting along the bars…

4. Forces P and F acting along the bars shown maintain equilibrium of pin A. Determine the values of P and F. Ans. P = 14.76 KN (C), F = 39 KN (T) 4 m 3 m 2 m 18 KN 30 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. calculate various angles and support reactions. 2. Using method of joints, calculate the forces…

Q: Problem 2. Calculate the area of the closed traverse or field in square meters (using coordinate…

A: Given data: Chainage (m) 0 25 50 75 100 125 150 Offset (m) 0 5.49 9.14 8.53 10.67 12.5 9.75…

Q: Water flows at 8m3/s through a rectangular channel 4 m wide and 3 m deep. If the velocity is 1m/s,…

A: Answer We are given Water flow rate Q = 8 m3/s At upstream section width of section at upstream b1 =…

Q: A beam will support a combination of dead, live, and earthquake loads. The Load Duration Factor for…

Q: Compute the elevation (orthometric height) for a station whose geodetic height is 113.991 m, if the…

A: N=-79m h=113.991m To find orthometric height

Q: Find the density of liquid whose specific gravity 1.221

A: Given- Specific gravity of the liquid-SG=1.221It is needed to find the density of the liquid ρ

Q: Question 1: A-find the zero force members of the truss shown below. B-Using section method determine…

A: Given :- Truss with a single load of 10 kN at point B. Required :- A) find the zero force members of…

Q: • The infiltration rate at the beginning of a storm is 100 mm/h and decreases to a constant value of…

Q: A steel cantilever beam is made of two st as shown in the Figure 2 below. Determin can carry. The…

Q: Workability of concrete is measured in a concrete lab by compaction factor test. If the partial…

A: Given, Compaction factor test result, Weight of partially compacted concrete = W1= 11.4kg weight of…

Q: Question: A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter…

Q: An activated sludge process (ASP) is designed for secondary treatment of 7500 m³/day of municipal…

Q: Two years ago, Snoop Lion deposited P15,000.00 in a fund that earns 10% interest compounded…

A: Given Interest rate = 10% compounded semiannualy 15000 deposited 2-years ago 10000 deposited today…

Q: 3.3m 2.2m 450N/m

A: Solution: Free body diagram:

Q: The maximum and minimum shear stresses in a hollow circular shaft of outer diameter 20mm and…

Q: P1. An asphalt concrete cylindrical specimen with a 4-in. diameter and a 6-in. height is subjected…

A: Given, Diameter of cylindrical specimen= 4 inHeight of specimen= 6 inAxial compressive load = 150 lb…

Q: 2. A 100 m tape is suspended at the ends under a pull of 15 kg. It has also supports at 30 m and 75…

Q: Determine the underflow volume of sludge wastage

A: Given, From figure, MLVSS,X=3000 mgl Underflow is maintained,Xu=12000 mglASP is designed for 7500…

Q: The force in AD

A: Given, A truss Free body diagram:-

Q: If the principal stresses in a plane stress problem, are 0₁ = 100 MPa, o₂ = 40 MPa, the magnitude of…

A: Given- Principal stresses- σ1=100 MPa,σ2=40 MPa, It is needed to find the magnitude of maximum shear…

Q: Q- A HOLLOW SHAFT Do = 2D, WHERE D. AND D, ARE THE OUTER AND INNER DIAMETERS RESPECTIVELY NEEDS TO…

A: Given- power P=20 KW,N=3000 RPM,shear stress τ=30 MPa,do=2d. It is needed to find the value of do.

Q: Find the maximum end moment capacity of a simply supported beam with W24 x 55 section, where Lb= 150…

A: Answer Let us first calculate Lp and Lr Lp = 1.76ryEFy Lp = 1.76*1.34*2900036 Lp = 66.94 in Lr =…

Q: 8- Determine maximum deflection. L 45 √2P → X

A: we will be able to get the equation of the elastic curve. where x and y are the coordinates shown in…

Q: Compute the safe wall thickness in mm of a 60-in steel tank with an internal pressure of 10 MPa. The…

Q: Describe something on the slide or figure that you understand, then create a question to ask a…

A: The image shows the graph drawn between the body's mass to the minimal weight and the specific cost…

Q: In the reinforced beam section shown in the figure (not drawn to scale), the nominal cover provided…

A: Given- cover=50 mm,diameter of the main reinforcement bar=16 mm,diameter of the strirrups=12 mm, It…

Q: 9. A surveyor sets up a transit at a point Q which is at the middle portion of a four-sided tract of…

Q: Compute the following: a. wall shear b. wall moment c. Deflection at mid-span

A: "Since you have posted question with multiples subparts , we will solve first three for you. To get…

Q: A noise meter located at a distance of 30 m from a point source recorded 74 dB. The reading at a…

A: Given data: Distance of 1st noise meter, R1=30 m Distance of 2nd noise meter, R2=60 m Sound recorded…

Q: Problem 3 Tangent segments intersect at station 25+15. The azimuth between the PC and the PI is 42…

Q: Is materials property data needed for Graphene Coating in Construction generated by experiment or…

A: This type of procedure is mainly done for increasing the strength of the structure. As it improves…

Q: A 10 m cantilever beam has a concentrated load of 10 KN at the free end. Find the maximum deflection…

Q: A leveling staff setup on point R of elevation (-8.79 m), is observed from point A where the three…

A: According to given Data leveling staff setup on point R of elevation = -8.79 m is observed from…

Q: what are the significance of specific gravity and Blaine fineness tests

A: Specific gravity The correct definition of specific gravity (sg) is the ratio of a substance's…

Q: A person by the name of Sutterland has developed a correlation that can be used to evaluate the…

Q: A grit chamber of rectangular cross-section is to be designed to remove particles with diameter of…

A: Given: Grit chamber dimensions Specific gravity of particles Diameter Settling velocity Flow…

Q: 1. t2myc पॉ C m D 5m E B 3im ↓ The block of mass m is suspended from the ring which is supported by…

Q: 4. The template shown below is typically used to portray matrix type of organizational structures…

A: If you need to manage multiple projects, it’s recommended to have a matrix organizational structure…

Q: A line was measured three times and yield the following results; 856.42, 856.69 and 856.12 m.…

A: Answer Probable error of the mean is given by Em = Esn Es = Probable error of a single measurement…

Q: E Listen Profile Level Notes: The elevation of BM A = 522.17' BS (plus sight) on BM A = 9.25' IFS…

A: Required :- elevation of the STA 0+00?

Q: Analyze the following beams and frames loaded with uniform, varying and concentrated loads.…

Q: A rectangular concrete channel has a bed slope of 0.001 terminates in a free outfall. The channel is…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: A 30 kg mass M is held in place by the 50 N force F1, cable OA and cable Find the mass m of the…

Q: What will be the nature of surface of pipe if the flow of water is taking place having roughness…

A: Given data: Roughness size, k=0.10 mm Average shear stress at pie boundary, τo=250 Nm2 v=10-6 m2sec

Q: Two steel spheres of diameters d, and d, where d₂= 2d,, are dropped from rest at the free surface of…

Q: Problem 4. Replace the three forces acting on the plate by a wrench. Specify the magnitude of the…

A: Given :

Q: While traveling along and against the traffic stream, a moving observer measured the relative flows…

A: Given- Case-1. Observer is moving along the traffic stream, q=50 vehicles/hr.VR=V-20. Case-2.…

Q: N. Draw a free body

Q: A solid sphere (diameter 6 mm) is rising through oil (mass density 900 kg/m³, dynamic viscosity 0.7…

Q: PROBLEM: Prove that the truss shown is statically determinate and solve for the force members. State…

A: Solution: Check for static determinacy: member = 21, reactions = 3 and joints = 12 m+r=21+3=24 2j =…

Question

Please answer with solution, and brief explanation, thank you.

4. Forces P and F acting along the bars shown maintain equilibrium of pin A. Determine
the values of P and F.
Ans. P = 14.76 KN (C), F = 39 KN (T)
4 m
3 m
2 m
18 KN
30 kN

5. Determine the pin reactions at A and all forces acting
on member DEF of the frame shown. Neglect the
weights of the members.
Ans. A = 60 KN, F = 28.30KN
6. Two cables are tied together at C and loaded as
shown. Determine the tension in cable AC and BC.
Ans. AC = 2.5 KN (T), BC = 2.72KN (T)
B
3.4 m
La
4.8 m
T с
2m
1.98 kN
3 m
3.6 m
1 m
40 kN-
2 m
B
1 m
A
2.5 m2.5 m-
x
D
F
60°
F
0.5 m
E
1 m
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the internal forces at point J when = 90 °.
Determine the internal force at member BC if X = 78.98 and Y= 70.45
Replace the distributed loading by an equivalent resultant force and specify where its line of action intersects a vertical line along member BC, measured from C.
Compute the value of EIy at 2.5 m from the left support.
NEED IN 1HOUR PLS THANKS From the figure, compute for the horizontal and vertical component forces of the hinge at B acting upon member AC as shown.
Dead Load= 20 kN/mLive Load= 30 kN/mUnit weight of concrete= 23.56 kN/cu.mf'c= 27.6 MPafy= 414 MPaCompute the shear and moment diagram.
From the beam shown. Let P = 40 kN, Q = 4 kN/m, L =8m. Determine: 1. Reaction at A. 2. Constant C1. 3. Slope at L/3. 4. Deflection at L/3.
Vertical Forces P & F in the figure produces a resultant of 500KN and a counter clockwise couple C of 250 KN-m. Find the magnitude of force P. a.) 1187.5 KN b.) -1687.5 KN c.) -1187.5 KN d.) None of the Above e.) 1687.5 KN
The force acting at A is F = 10i + 20j − 5k kN. Knowing that the moment of this force about the y-axis is 8j kN · m, determine the distance b and the moment of F about point O.
Note : point load = 12.289KN/m *3 = 36.867KN . 1) calculate the reaction forces 2) Calculate and draw the Bending moment digram, and what is the value of maximium bending moment ? 3) calculate and draw the shear force digram and what is the value of the maximum shear force ?
Determine the shear value (kN) when x = 2.2m from the left side of the beam where: L = 4.9 m; Wo = 131 kN/m
Determine the magnitude of the projectedcomponent of the force F = 300 N acting along line OA.