4. The armature of a four-pole DC generator has 90 slots on its armature with 6 conductors per slot. If the armature is lap-wound, flux per pole is 6 × 10-2 Wb and running at 1000 rpm, determine its induced emf. Also determine the electrical power output of the machine if the current per conductor is 100 ampere. (Ans. 540 V; 216 kW)

4. The armature of a four-pole DC generator has 90 slots on its armature with 6 conductors per slot. If the armature is lap-wound, flux per pole is 6 × 10-2 Wb and running at 1000 rpm, determine its induced emf. Also determine the electrical power output of the machine if the current per conductor is 100 ampere. (Ans. 540 V; 216 kW)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 35 kW, 400 V, short shunt, compound dc generator has a full load efficiency of 85 %. If the resistance of the armature and interpole is 0.35 ohm and that of the series and shunt fields are 0.15 ohm and 220 ohms respectively. Calculate the following: Output of the prime mover = kW Power developed in the armature = kw Total Copper Losses = kw Combined bearing friction, windage and core loss = kw
An 8-pole dc generator has 500 armature conductors, and useful flux of 0.05 Wb perpole. What will be the emf generated if it is lap connected and runs at 1200 rpm? Whatmust be the speed at which it is to be driven to produce the same emf if it is waveconnected and the flux is reduced to 80% of its value when lap connected?
7) The flux per pole of a four-pole generator is 0.05 wb. It driven at a speed of 1500 rpm. In order to have an induced emf of 20 v per conductor, , if the winding is lap-connected, find (a) the number of conductors in series in each parallel path, (b) the number of conductors between brushes to generate 240 v, and (c) the total number of conductors in the armature.
A 150-kW 250-volt compound generator is connected long shunt. If the shunt field resistance is 20 ohms, what is the series field-current at full load? (Ans.: 612.5 A) write diagram, given, etc
Problem: A self-excited shunt generator has a field resistance of 52 ohms. When the generator delivers 7 kW, the terminal voltage is 6 V, while the generated emf is 7 V. Determine the armature resistance in ohm.
please answer in bond paper 3. A long-shunt, four pole, 1500-W, 250-V, duplex wave-wound DC compound generator with the rated speed of 500 r.p.m., has a shunt field resistance of 100 Ω, a series field resistance of 0.05 Ω and an armature resistance of 0.2 Ω. If the flux per pole is 48.798 mWb and a total of 620 conductors, calculate the following: (a) the generated voltage, (b) the field currents, (c) the power generated in the armature.
5. A 4-pole, d.c. shunt generator with a shunt field resistance of 100 Ω and an armature resistance of 1 Ω has 378 wave-connected conductors in its armature. The flux per pole is 0.02 Wb. If a load resistance of 10 Ω is connected across the armature terminals and the generator is driven at 1000 r.p.m., calculate the power absorbed by the load.
A compound DC generator has a series resistance divided equally and connected in series with the load and the armature. If this generator is rated at 720 V with an armature resistance of 0.1 Ω, shunt resistance of 240 Ω and a (total) series field resistance of 0.6 Ω, find the generated emf if it delivers 100 A?
A 4-pole lap -wound dc generator is designed to have an average airgap flux density of 0 .8 T. The armature winding resistance is 0 .3 Ω, and the brush contact drop is 1 V. There is a slight fault in the magnetic circuit which causes the emfs in two of the paths to be 5 %more than the nominal value, and the emfs in the other two paths 5 %less . a) If the generator supplies a full load of 4 .5 kw at 150 V, find the nominaland actual values of path emfs, coil currents, and armature copper loss. b) Find the nominal and actual values of coil currents and armature copperloss when the generator has no external load.
A series generator having a combined armature and field resistance of 0.4 ohm usrunning at 1000 rpm and delivering 5.5 kW at a terminal voltage of 110 V. If thespeed is raised to 1500 rpm and load adjusted to 10 kW, find the new terminalvoltage. Assume the machine is working on straight line portion of magnetizationcharacteristics.
. When a self-excited compound DC generator supplies load, the terminal voltage is not the same as the generated emE Why? a) voltage drop across the armature resistance will reduce the voltage available at the load terminals b) where there is a series field, voltage drop across the series field resistance will reduce the voltage available at the load terminals c) both "a" and "b" d) neither "a" nor "b"
44 - A - the regulation curve of a DC generator shows the relation between what two factors? a) output voltage and load current, b) output voltage and field current, c)field current and load current, d) none B) If same DC generator ca be connected for either separate- or self-excitation, with of the two connections should be used to obtain the better voltage regulation? a) self-excited b) separately-excited C) How is the efficiency usually expressed? a) in waltts, b) in kilowatts-hours, c) in percentage, d) none