4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The uniform load is service load consisting of 50% dead load and 50% live load. The dead load includes the weight of the beam. Use A36M steel materials and Determine the service superimposed dead load and live load in (kN /m) can be applied on the member. tum. |--1.8² 5.4m T -1.8mx|

4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The uniform load is service load consisting of 50% dead load and 50% live load. The dead load includes the weight of the beam. Use A36M steel materials and Determine the service superimposed dead load and live load in (kN /m) can be applied on the member. tum. |--1.8² 5.4m T -1.8mx|

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the given frame shown, analyze using cantilever method: Which of the following gives the axial load for column BD?a. 22.5 kN c. 82.5 kNb. 62.5 kN d. 45 kN Which of the following gives the shear at column DF?a. 45 kN c. 30 kNb. 95 kN d. 50 kN Which of the following gives the moment at support B?a. 160 kN-m c. 140 kN-mb. 150 kN-m d. 120 kN-m
q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.787 m, b = 1.901 m, and L= 5 M.For a load of P = 136 kN, determine thedisplacement of joint D. Unit should be in mm
A cantilever beam with length of 3.2 m is reinforced with As=5720 mm^2 tension reinforcement and compression reinforcement A's =1905 mm^2 placed at 60 mm from extreme compression fiber. The effective depth is 550 mm and width of 400 mm. Use f'c=35 MPa and fy=415 MPa. 1. Calculate the magnitude of the neutral axis. 2. Determine the compressive force of the section. 3. Determine the safe concentrated live load that can be placed at the free end if the beam carries a total ultimate uniform load of 35 kN/m.
A cantilever R.C. beam is 280 mm x 500 mm deep and is reinforced with 4- 20 mm diam bars for tension. Using an effective depth of d = 450 mm, determine if the 2.50 m long beam is adequate to carry a uniform load of 15 KN/m and a concentrated load of 10 KN at the cantilever end in 2 ways. Use f’c = 21 MPa, fy = 275 MPa. Neglect the weight of beam. Use n = 9.Determine if the catilever beam is adequate based on strength design 2001 NSCO specifications. The 15Kn/m load is DL while the 10KN load is LL.
q2: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.705 m, b = 1.821 m, and L= 4 M.For a load of P = 117 kN, determine thedisplacement of joint F. Unit should be in mm
A short spiral column carries an axial dead load of 118 kN and an axial live load of 235 kN. Use fc’ = 27.5 MPa, fy = 414 MPa. Use U = 1.2D + 1.6L, Ф = 0.65 1. Assuming ρ = 0.01, which of the following gives the diameter of the column section? * a. 200 mm b. 215 mm c. 220 mm d. 300 mm 2. Which of the following gives the number of 16 mm diameter main bars? a 3 pcs b. 4 pcs c. 5 pcs d. 6 pcs 3. Which of the following gives the spacing of spirals? a. 10 mm Ф b. 55 mm Ф c. 60 mm Ф d. 65 mm Ф
A wood beam AB on simple supports with spanlength equal to 10 ft is subjected to a uniform load ofintensity 125 lb/ft acting along the entire length of thebeam, a concentrated load of magnitude 7500 lb acting ata point 3 ft from the right-hand support, and a momentat A of 18,500 ft-lb (see figure). The allowable stresses inbending and shear, respectively, are 2250 psi and 160 psi.(a) From the table in Appendix G, select the lightestbeam that will support the loads (disregard theweight of the beam).(b) Taking into account the weight of the beam(weight density = 35 lb/ft3 ), verify that theselected beam is satisfactory, or if it is not, selecta new beam.
A steel tank 2m by 1.5m by 1.2m weighs 10KN when empty and is supported by two steel beams spanning 2.0m and each weighing 10KN. Design a suitable square section for the steel beams if the tank is filled water weighing 10KN/m^3 using the plastic method. The permissible bending stress on the section is 140N/mm^2 and factor of safety is 1.5
3.5 (A). A beam AB, 3 m long, is simply-supported at A and E. It carries a 16 kN concentrated load at C, 1.2 m from A, and a u.d.1. of 5 kN/m over the remainder of the beam. Draw the S.F. and B.M. diagrams and determine the value of the maximum B.M.
Compute the location and maximum value of elastic equation curvefor the beam loaded as shown. a
Consider the following framing plan below. Squares labeled A through L are columns. All girders have rectangular sections with width 300 mm and depth 600 mm. Slab thickness is 125 mm. Superimposed dead load for the entire floor is 2.95 kPa and live load for the entire floor is 4.8 kPa. For self-weight of the floor system, use unit weight of RC of 23.6 kN/m3. a. Considering continuous girder DEF, determine the maximum factored positive & negative moments Mu (+) & Mu (-), as well as the factored shear Vu that should be used for the design of the said girder. Use ACI moment & shear coefficients to draw the factored shear & moment diagram of the said girder.
USE 3 decimals; DRAW FREE BODY DIAGRAMS A 9-m simple beam is carrving a uniform load or 25 kN/m over the entire beam with two-point loads of 15 kN at 1.5 m from both ends. If E = 200 Gpa and | = 0.000332 m^4, determine the following using the Double Integration Method:a.) Midspan deflectionb. Deflection at 1.5 m from the eft reaction