4. The signal to noise ratio on your phone line is 1000:1 and your modem ttempts 7000 symbols per second, with each symbol representing 6 bits. a) What is the data rate that your modem is attempting? b) If the bandwidth on the line is 3000 Hz, what is the maximum theoretical data rate? c) Check all three limits, show your work. Which of the three limits were exceeded?

4. The signal to noise ratio on your phone line is 1000:1 and your modem ttempts 7000 symbols per second, with each symbol representing 6 bits. a) What is the data rate that your modem is attempting? b) If the bandwidth on the line is 3000 Hz, what is the maximum theoretical data rate? c) Check all three limits, show your work. Which of the three limits were exceeded?

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 2PE

See similar textbooks

Similar questions

1) What is the major factor that makes coaxial cable less susceptible to noise than twistedpair cable? (a) Inner conductor (b) Diameter of cable (c) Outer sheath (d) Insulating material 2) Aliasing can be defined as errors occurring when (a) The sample rate exceeds twice the input frequency.(b) The bandwidth is less than the input frequency.(c) The number of bits per sample is low.(d) The sampling signal has been incorrectly identified. 3) In _______encoding, three levels are used: positive, zero, and negative. (a) Unipolar RZ (b) Bipolar RZ (c) Polar NRZ (d) Manchester NRZ 4) The ________ rate defines the number of data elements sent in 1sec; the ______ rate isthe number of signal elements sent in 1sec. (a) data; signal (b) signal; data (c) bit; baud (d) baud; bit5) The channel capacity of a noiseless channel can be improved by (a)Increasing the signal-to-noise ratio. (b) Decreasing the channel bandwidth.(c) Applying error correction technique. (d) Applying M-ary modulation scheme. 6)…
A mobile station traveling at a speed of 60 km/h transmits at 900 MHz. If it receives or transmits data at a rate of 64 kbps, is the channel fading slow or fast?
What is the maximum data rate if that same system is subject to noise, with an average power level of 600 and an average noise level of 200?
A line has a signal-to-noise ratio of 1000 and a bandwidth of 4000 kHz. What is the maximum data rate supported by this line? If the bandwidth of the channel is 5 kbps, how long does it take to send a frame of 100,000 bits out of this device? What is the maximum data rate of a channel with a bandwidth of 200 kHz if we use four levels of digital signaling?
Four channels, two with a bit rate of 120kbps and two with a bit rate of 880kbps, are to be multiplexed using multiple-slot TDM with no synchronization bits.Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame? d. What is the data rate?
Assume having a low-pass channel that spans from a Frequency of 0Hz to 110Hz, to attain a bit-rate value that is not less than 1Kbps, then among the following, the minimum value of the signal to noise ratio must be: Select one: A. None of the mentioned choices is correct B. 1023 C. 511 D. 15 E. 31 F. 127 G. 255 H. 63
Suppose, BanglaLink has 4 voice channels, each of 60Mbps. They use synchronous TDM to multiplex these channels. If 3 characters at a time are multiplexed (3 characters in each output slot), 1. Draw the first two output frames with arbitrary inputs. 2. What is the size of an output frame in bits? 3. What is the output frame rate? 4. What is the duration of an output frame?
Assume digitizing a voice signal that is cartied over a dialup channel, the minimum number of samples you need to collect per second equals?
In a digital transmission, the receiver clock is 0.1 percent faster than the sender clock. How many extra bits per second does the receiver receive if the data rate is 2 kbps? How many if the data rate is 2 Mbps?
16. Which one is not transmission impairment?a) Distortion b) Attenuation c) Signal d) Noise e) None17. If two signals, which carry data of the same type, interfere each other, then data in onechannel embeds into other. This is called:a) Noise b) Crosstalk c) Spectrum d) Attenuation e) None18. Which one of the followings cannot be improved at a constant temperature?a) Signal-to-noise ratio b) Bandwidth c) Signal powerd) Noise Power e) None19. Which one is a disadvantage of wired communication?a) Is useful only for point to point communicationb) Only a small partition of transmitted energy can be received, since energy distributeseverywherec) Useful bandwidth is less than other wireless transmissiond) It is requires more complex circuitse) None21. Which one is used to describe methods that enable transmission of two or more signalswith the same transmission system?a) Encoding b) Multiplexing c) Modulating d) Spectrum e) None
58. In a digital transmission, the receiver clock is 0.1 percent faster than the sender clock. How many extra bits per second does the receiver receive if the data rate is 1 Mbps? a. 10 bps b. 100 bps c. 1000 bps d. 10000 bps
8. Which of the following performs modulation and demodulation? a. fiber optics b. switch c. modulator d. modem