4. We want a peak load voltage of 40 V out ofabridge rectifier. What is the approximate rmsvalue of the secondary voltage?5. What is the peak load voltage out of a bridgerectifier for a secondary voltage of 12.6 V,rms?(Use second approximation.)6. If line frequency is 60 Hz, what is the outputfrequency of a half-wave rectifier?7. If line frequency is 60 Hz, what is the outputfrequency of a bridge rectifier?8. If the load current is 5 mA and the filtercapacitance is 1000 F, what is the peak-to-peakripple out of a bridge rectifier?9. The diodes in a bridge rectifier each have amaximum dc current rating of 2 A. What is themaximum value of the dc load current?10. What is the PIV across each diode of a bridgerectifier with a secondary voltage of 20 V,mg?rms

As per the guidelines of bartleby, we have to solve first 3 questions among the multiple subpart…

4. We want a peak load voltage of 40 V out ofa bridge rectifier. What is the approximate rms value of the secondary voltage? 5. What is the peak load voltage out of a bridge rectifier for a secondary voltage of 12.6 V,rms? (Use second approximation.) 6. If line frequency is 60 Hz, what is the output frequency of a half-wave rectifier?

4. We want a peak load voltage of 40 V out ofa bridge rectifier. What is the approximate rms value of the secondary voltage? 5. What is the peak load voltage out of a bridge rectifier for a secondary voltage of 12.6 V,rms? (Use second approximation.) 6. If line frequency is 60 Hz, what is the output frequency of a half-wave rectifier?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 2500-V, 2-A, dc power supply is to be designed with a ripple voltage ≤ 0.5 percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b) What is the minimum PIV rating for the diode? (c) What is the rms value of the transformer voltage needed for the rectiﬁer? (d) What is the peak value of the repetitive current in the diode? (e) What is the surge current at t =0+?
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, The transformer is specified to have a 12 V rms secondary voltage for the standard 110 V across the primary. (2nd Approximation)
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
1. Draw and briefly explain the ideal characteristics of PN-junction diode ? 2. Explain briefly about avalanche and Zener breakdown ? 3. In which region can Zener diode be used as a regulator? Why? 4. What is the ripple factor? For a good filter, should the ripple factor be high or low? 5. What is a rectifier? What is the difference between a full-wave rectifier and a half-wave rectifier?
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 4. The value of dc current (Idc) in amperes is ? 5. The value of the output peak voltage (Vpout) in volts is ? 6. The value of peak secondary voltage (Vpsec) in volts is ? 7. The value of primary peak voltage is (Vppri) in volts is ?
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is ? 2. The value of the dc voltage (Vdc) in volts is ? 3. The value of the ripple factor is ?
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
Explain the operation of both signal- and three-phase rectifier circuit by making reference to the sketched waveform.
what is the purpose of installing a filter capacitor in a bridge rectifier circuit? Why don't we install a zener diode which reduces the ripple voltage or to get a consistent voltage wave at Vout?
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 Ω? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is ﬁrst applied? (e) What is the amplitude of the repetitive current in the diode?