I need the answer as soon as possible 4. What is the culvert bottom slope denotedas?a) slb) SLc) Sod) sL

The culvert bottom slope denoted as c) So Other , options doesn't exist. Correct option is C

Answered: 4. What is the culvert bottom slope…

Engineering

Civil Engineering

4. What is the culvert bottom slope denoted as? a) sl b) SL c) So d) sL

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter16: Highway Drainage

Section: Chapter Questions

Problem 17P

See similar textbooks

Related questions

Q: 5. What is the Froude's number for a channel having mean velocity 4.34 m/s and mean hydraulic depth…

A: To find : Froude's number.

Q: . The alternate depth of an open channel section is most dependent on which factor? Group of answer…

A: Option A is correct ( flow rate ) Alternate depth is depth at which specific energy is same . Here…

Q: PROBLEM 3 Water is to flow at a rate of 30 m³/s in the concrete channel (n = 0.013) with the…

Q: Question 23 Determine the hydraulic depth D (average depth) of a triangular channel with right angle…

Q: Determine the hydraulic depth D (average depth) of a triangular channel with right angle corner…

A: Y=3m

Q: The cross section of a channel is said to be best if the: а. Hydraulic mean depth is maximum b. none…

Q: 1. Determine the Hydraulic depth for a triangular channel having side slope of 1H:3V and depth 15m.…

A: Given data: Side slope= 1H:3V Depth =15 m Hydraulic depth =?

Q: A hydraulically efficient trapezoidal channel section has a uniform flow depth of 2 m. The bed width…

A: Given data in question Hydraulically efficient channel Trapezoidal channel Uniform flow depth To…

Q: derive a general expression for the wetted perimeter of a trapezoidal channel in terms of…

Q: Compute the volume of fill per unit length for an earth dam 9.0m high , assuming a top width of 2.4m…

A: Given dam 9.0m high , a top width of 2.4m , sideslope of 3:1 upstream and 2:1 downstream

Q: Design an irrigation channel in alluvial soil according to Lacey's silt theory with the following…

Q: ficient is 6 cm/day, determine the required capacity and the suitable section of the channel for…

A: Given:- area=500ha drainage coefficient=6cm/day side slope=1:1 Lacey's silt factor=1.0 To find:-…

Q: What is the regime scour depth for a channel in soil with silt factor of unity and carrying 8 m2/s…

A: Given data : Discharge per unit width (q)=8 m2/sSilt factor (f)=1

Q: Using simplified arch-rip analysis, design an arch dam 180 m high for a trapezoidal canyon having…

A: Arch dams can be designed by using following methods 1 Thin Cylinder theory 2 Theory of elastic…

Q: Determine the Hydraulic radius if area oc channel is 20 m2 and wetted perimeter is 14 m

A: Given Area 20m^2 Wetted perimeter 14m Hydraulic radius ?

Q: A channel designed by Lacey's theory has a mean velocity of 1.1 m/s. The silt factor is 1.1. Then…

A: given- mean velocity v=1.1 m/ssilt factor f=1.1

Q: 2. For a trapezoidal channel with a bottom with of 6 m, side slope of 3 horizontal to 1 vertical,…

Q: A rectangular channel 3m wide on a mild slope has streamlined sill constructed across the channel.…

A: b= 3 mQ= 6 m3/sy= 1.35 mq=Qb= 63=2 m3/s

Q: Consider a farm irrigation ditch in a loam soil having the following dimensions: a) Bottom width,…

A: (a) Cross-sectional area of the stream: = width of channel * depth of water = 0.50 meters * 0.40…

Q: A meter diameter reinforced concrete pipe culvert is flowing 3/4 full. It's wetted perimeter "p" is…

Q: Through the smooth transition between two rectangular channels the width increases from 3.0 m to 3.6…

Q: The flood discharge under a bridge is 200 m3 / s. If the river bed has a deep layer of coarse sand…

A: Given, Q = 200 m3/s f = 1.5 Find, Maximum scour depth

Q: The cumulative volumes at St.Km’s 0+150 and 0+180 are 2025 and 1875 m3 respectively. If at the…

A: Givencumulative cut volumes at station 0+150 =Vcut=2025m3cumulative fill volume at station 0+180…

Q: An alluvial stream (d = zero.60 mm) has a bed slope of 3 x 10-4 locate the imply speed of drift…

Q: find Gs If e =0.75, hc =2.81 m, Z= 3m Where: Z: soil thickness hc: Critical hydraulic gradient e:…

A: Given data : The value of void ratio e=0.75 The value of critical hydraulic gradient iC=2.81 To…

Q: A trapezoidal channel has a side slope of 20° to the vertical and has a base width of 150 m. If the…

A: Given that, for a trapezoidal channel side slope = 20 o to the vertical base width = 150 m Depth of…

Q: Design an irrigation channel in alluvial soil according to Lacey's silt theory with the following…

Q: A channel designed by Lacey's theory has a mean velocity of 1.1 m/s. The silt factor is 1.1. Then…

Q: Water flows through a 0.3-meter-deep triangular channel (apex down). The apex is at a 90-degree…

A: Given Depth of triangular channel ,Y1 = 0.3 m Depth of hydraulic Jump ,Y2= 0.9 m

Q: Find the hydraulic radius Wetted area=6.25 m2 Wetted perimeter=7.5 m

Q: If for a certain channel, the Lacey's silt factor is 0.95, side slope is 1: 1 and bed slope is 1 in…

Q: A trapezoidal channel with a bottom width of 4.00 feet and side slopes of 2 horizontal to 1 vertical…

Q: 5.a. Define section factor and hydraulic exponent? Derive an expression for most efficient…

Q: width (8 m) and grade line for the road is lateral inclination is 1:1. The distance between the…

Q: Find the hydraulic radius if wetterd area is 11 m2 and wetted perimeter is 8 m

A: ASKED: To compute the hydraulic radius. Given, Wetted area (A) = 11 m2 Wetted perimeter (P) = 8 m

Q: 1. Estimate the hydraulic depth for a most economical circular channel section in case of maximum…

A: To find : Hydraulic depth.

Q: what is confined and unconfined aquifer? What are their differences?

A: A confined aquifer is condition where the ground water table of water mass is confined between two…

Q: A trapezoidal channel has a bottom width of 1m and side slopes of 2H:1V. If the depth of flow is 4…

Q: If the water depth immediately upstream or downstream of a frictionless vertical moving cover in a…

A: Given data: Depth at upstream (Y1)=0.3 mVelocity at upstream (V1)=6 m/s

Q: A trapezoidal channel has a bottom width of 6.0m, side slopes of 2 vertical: 4 horizontal, and…

A: Bottom Width (B)=6m Side Slope(1:n)= Vertical:Horizontal n=42 n=2 Discharge(Q)=17m3/s channal bed…

Q: Question: What is the regime scour depth for a channel in soil with silt factor of unity and…

Q: Question 7 Determine the hydraulic depth D (average depth) of a triangular channel with right angle…

A: Determine the hydraulic depth D?

Q: Question 5 Determine the section factor (Z) of a triangular channel with right angle corner (90°)…

Q: If the water depth immediately upstream or downstream of a frictionless vertical moving cover in a…

A: Discharge is the main quantity in any sector that is used to transfer fluid from one place to…

Q: Refer to the following channel cross section. Normal depth is 3.0 feet. (a) What is the…

Q: Design a channel section by Kennedy's theory given the following data : Discharge Q = 28 cumecs…

Q: A drainage canal in the shape of trapezoid with a bottom width of 2,3m and a side slope of 1…

Q: Hydraulic mean depth of rectangular channel having base width 4 m and depth 20 m will be ?

A: Given: Base width of rectangular channel, b= 4 m Depth, d=20 m To find: Hydraulic mean depth, R

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

4. What is the culvert bottom slope denoted
as?
a) sl
b) SL
c) So
d) sL

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a semi-circular open channel (n=0.014) that is anticipated to convey 25cumecs of water. The slope of the channel bed is 0.0015. Solve the hydraulic depth of the designed section.
The cumulative volumes at St.Km’s 0+150 and 0+180 are 2025 and 1875 m3respectively. If at the latter St.Km., Lcut = 10 m and average fill area is twice the average cut area, find these average areas.
A trapezoidal canal has one side vertical and the other sloping 1:1. The discharge is known to be 20 m³/s at a mean velocity of 1.2 m/s. If the slope is to be minimum as possible, and n=0.015, (a) At what depth is it flowing in m? (b)What is the value of this minimum slope? Please answer this immediately. Thank you!
Sketch the water surface profile with full details if the channel bed slope is changed according to the following: a) Mild to steep to steeper, b) Steep to horizontal to mild, (explain each steps)
A rectangular channel of best hydraulic cross-section, n = 0.016, is laid on a slope of 0.0064 and carries 98 m³/ s. For critical conditions, what with is required?
Design a semi-circular open channel (n=0.014) that is anticipated to convey 20cumecs of water. The slope of the channel bed is 0.0015. Solve the hydraulic radius of the designed section.
If the overall outside answer of the reinforced concrete pipe to be installed is 95 cm, and the top of the culvert is 30 cm below the subgrade, what will be the invert elevation at the center?
In a hydraulically most efficient trapezoidal channel section the ratio of the bed width to depth is O a. o b. O ¢ o d. 0.5 0.86 1.155 0.707
An elliptical culvert is 3.5 feet tall and 9 feet wide. It is filled with water to a depth of 1.05 feet. Find width of the stream.
Question: Explain Design of Canal fall at change point of slope Subject: irrigation engineering
Water flows at a depth of 10 cm. with a velocity of 6 m / s in a rectangular channel. Is the flow sub-critical or super-critical? What is the alternate depth?
A sharp-crested weir 3.0 ft high extends across a rectangular channel 20 ft wide in which there is 100 cfs flowing. Determine the depth of water upstream from the weir. Draw the sketch.