4.15 The 480-kg bent bar ABC of uniform cross section is supported by a pin at A and a vertical cable at C. Determine the pin reactions and the force in the cable. y i. A, A - Ag 2 m T WAB=160(9.81) N C B 4 m 2 m 2 m WBC= 320(9.81) N %3!

4.15 The 480-kg bent bar ABC of uniform cross section is supported by a pin at A and a vertical cable at C. Determine the pin reactions and the force in the cable. y i. A, A - Ag 2 m T WAB=160(9.81) N C B 4 m 2 m 2 m WBC= 320(9.81) N %3!

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: B. The bent beam ABC is attached to pin at C and rests against a roller support at B. Neglecting the…

Q: HW 2 A cable is attached to the plate B of weight W, passes over a fixed peg at ingsand is attached…

A: Consider the following free body diagrams: Figure 1. Figure 2. The equilibrium conditions are as…

Q: Problem 1- The beam shown below is in equilibrium when subjected to forces presented. Determine the…

Q: Determine the vertical support reaction at point A.

Q: 1. Determine the moments in the beam at A, B. C, and D. 12m What is M in kN-m? MA = MB = Mc = MD = B…

Q: What is the maximum moment at midspan in the following beam? P, Pz

Q: X N/m Y N/m A B Am В m 1. What is the total resultant vertical load in the beam AB? (N) 2. At what…

Q: Determine (approximately) the internal moments at A and B caused by the vertical loading. 3 kN/m G F…

Q: The boom of the derrick in the figure is rotated back 30° from the XY plane. Determine the force in…

A: Structural engineering can incorporate an assortment of administrations for the investigation and…

Q: Q5: If P = 0 and F = 8 kN, what would be the relation between the reactions at the support will be?…

A: Option C) RA= RB is correct

Q: 5KN/m

Q: 8.28 The rectangular beam ABC, 100 mm wide by 400 mm deep, is supported by a pin at A and the cable…

Q: Roller 100 kN B El, constant Q1) Compute the horizontal displacement of the roller at D and the…

A: Calculate the reaction:RA+RD=0∈MA=0RD×6-100×6=0RD=100KNRA=-100KNHA=100KN When unit load placed at…

Q: 150 kN 40 kN/m Determine the vertical reaction at support B of the given frame. 8 m 20 kN/m 6 m 6 m…

Q: 10.Determine P so that the moment at each support is equal to the moment at midspan. Show your…

Q: F1 E F A D F2

Q: 625 mm? 1250 mın? 120 cm -60 cm --- 90 cm figure 3.1 Calculate the force P2 necessary for…

Q: 1.5 m 1.5 m Im 1.5 m S00 N/m 3 m 1.5 m1 m" 3 m

A: The dimensions in x ,y and z directions are given

Q: Determine (approximately) the internal moments at A and B caused by the vertical loading. 3 kN/m G F…

A: Draw the free-body diagram of the frame as follows. Draw the reaction diagram of the segment GL.…

Q: Q.5: A beam of channel section 120 mm x60 mm has uniform thickness of 15 mm. Determine the shear…

Q: Determine (approximately) the internal moments at A and B caused by the vertical loading. 3 kN/m F K…

Q: 4.15 The 480-kg bent bar ABC of uniform cross section is supported by a pin at A and a vertical…

A: Free body diagram is given below

Q: 1. Determine the shear force and bending moment at point C. 10 kN/m 50 kN-m 3m +1.5m 1.5m

A: given:-

Q: P kN В W kN/m 12 m A 5 m 5 m Draw the schematic / blown-up diagram of the frame showing the member…

Q: 200kN 200kN A C ¿D E 3m 3m 3m 3m El= Constant a. Using the force method draw the primary structure…

A: Force method: The force method is used to analyze the statical indeterminate structures. The force…

Q: Q.2) For the truss shown in figure below, determine the forces in lo00 TD 2000 N LE in 2/E to JE

Q: Determine the support reactions at A and B. B 15 12 000 L=26

Q: 1. Determine the shear force and bending moment at point C. 10 kN/m 50 kN-m 3m +1.5m +1.5m A

Q: Example Determine the support reactions at the roller at A and the pin at B. Neglect the weight and…

Q: Determine the vertical and horizontal displace-ments at A of the pin-connected structure in Figure…

A: Solution:

Q: TK C 2 m 1 m 25KN

A: Determine shear force at point c in above diagram.

Q: From the continuous beam show, determine the Moment at CO, Mcp in kim 250 kN 20 kN/m D 12 m 12 m 4 m…

Q: Q1/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg)…

Q: Determine the Support Reaction of the Beam shown below 19 40kn/m 'D' kN 20kn/m

Q: and P2 = 12 kN .

Q: Please Solve this question

A: The given data is shown below

Q: Determine the internal bending moment (kN-m) at point D. 1.5 kN/m 0.5 kN/m A B D 6 m 3 m

Q: for steel beam in Figure Q3. Point D is located just to the right of the concentrated force and…

A: To find internal forces at point D and C

Q: Problem #2 Y kN В m A B Y kN 8 kN Am C m 2 m 6. What is the reaction of the support at B? (kN) 7.…

Q: Determine the moment M in kN-m that must be applied to the beam to create maximum stress of 98 MPa.…

A: Determine the moment M in kN-m that must be applied to the beam

Q: 7. The uniform 150-kg bar AB shown in Figure 5 carries a 2KN vertical force at A. the bar is…

Q: 2. Determine the horizontal and vertical components of force at pin B and the normal force the pin…

Q: The 510-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

Q: The pin-jointed frame work in the figure If a vertical D F. concentrated load of 800KN (downward)…

A: As per guidelines we need to answer only 1st three subparts of question

Q: The system in the figure is in equilibrium. A concrete block of mass 232 kg hangs from the end of…

A: Take moment about hinge:Tsinθ-ϕL-mgL2cosθ-m'gLcosθ=0

Q: If M = 5.41 and w = 26.4, Determine the Shear Force at point B of the Beam shown. w in kN/m Min kN.m…

A: Given data in question Cantilever beam Span member length UDL Concentrated moment To find out…

Q: 5.58 The homogeneous 860-kg bar AB is supported by a ball-and-socket joint at A and two cables…

A: Co-ordinates of point A = (0,0,0)m Co-ordinates of point B = (-4.5,0,4)m Co-ordinates of point C =…

Q: Q4) The 50 kg pot in Fig (4), is supported from A by the three cables. Determine the force acting in…

Q: D 3 ft 5 ft 5 ft B The homogeneous 6000-lb bar ABC is supported by a pin at C and a cable that runs…

A: Given data in question Span member length Weight of Bar Hinge at point C Diameter of cable To find…

Q: Q2: - The weight W= 10 kN hangs from the cable, which passes over the pulley at F. Neglecting the…

A: ∑MA=0Ey4+W(2-0.4)=0Ey=4 KN

Question

4.13 Calculate the force P that is required to hold the 600-N roller at rest on the
rough incline.
4.14 Solve Prob. 4.13 if the force P pushes rather than pulls.
4.15 The 480-kg bent bar ABC of uniform cross section is supported by a pin
at A and a vertical cable at C. Determine the pin reactions and the force in the
15°
2 m
cable.
150
LI
A
| 600 N
2 m
P
15°
2 m
WAB=160(9.81)N
T
B
4 m
B
C
2 m
2 m
WRC = 320(9.81) N
FBD
F
Fig. P4.15
FBD
Fig. P4.14

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the reactions and the expected horizontal displacement at point D by applying 1 unit load at D directed to the right.
2.3. The direction of the 75-lbf force may vary, but the angle between the forces isalways 50 degrees. Determine the value of ? for which the resultant force actingat A is directed horizontally to the left. 1 Free-body Diagram only
DETERMINE THE FORCES IN MEMBER AB AND BC IF P = 2500 N.
Dam is concrete gravity dam that impounds water both on the upstream and down stream sides. if the coeffient of friction between the base and the dam is 0.34, determine the following: 1. total vertical reaction in kN 2. total horizontal reaction in kN 3. factor of safety against sliding 4. factor of safety against over turning 5. if the hydrostatic uplift varies linearly from 0 at the heel to zero at the toe, determine the foundation pressure.
Determine the reactions and all bar forces for thetruss in Figure P9.34. E = 29,000 ksi and members AB,BC, AD, and DC have A = 3 in.2, and members BD, DE,and CE have A = 1 in.2 for all bars.
determine the shear force and bending moment at point 1 (P1) in the figure.
If P = 20.3 and M = 6.83, Determine the Shear Force at point B of the Beam shown.
(a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure P8.10. For all bars, area = 2400 mm2 and E = 200 GPa. (b) Assuming that no load acts, determine the horizontal displacement of joint B if support A moves 20 mm to the right and 30 mm down and support E moves downward 36 mm.
Determine the horizontal and vertical deflection of the hinge at point C of the arch in Figure P8.16 for a single concentrated load of 60 kips applied at joint B in the vertical direction.
Solve for the reactions and moments at the supports below using moment distribution method. Answer: Ra=110.2 kN, Rb=310 kN, Rc=220 kN, Ma=-125 kN m, Mb =-259 kN m, Mc = -160 kN m
For the truss in Figure P8.3, compute the horizon-tal and vertical components of the displacement of jointC. The area of all bars = 2500 mm2, and E = 200 GPa.
The figure which is in equilibrium under the forces P and F = 42 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress in the pin if it is 21-mm-diameter.