400 circumferential fins of rectangular profile (k = 386 W/m oC) are installed on a tube having a diameter of 3 cm and 1 m length that is maintained at a temperature of 200oC. The single fin has a length of 2 cm and a thickness of 0.7 mm. The heat is transferred to the surrounding air at 100oC with a convection heat-transfer coefficient of 524 W/m2 oC. How many times is the heat transfer rate enhanced when the fins are installed on the tube?

400 circumferential fins of rectangular profile (k = 386 W/m oC) are installed on a tube having a diameter of 3 cm and 1 m length that is maintained at a temperature of 200oC. The single fin has a length of 2 cm and a thickness of 0.7 mm. The heat is transferred to the surrounding air at 100oC with a convection heat-transfer coefficient of 524 W/m2 oC. How many times is the heat transfer rate enhanced when the fins are installed on the tube?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.36P

See similar textbooks

Similar questions

Calculate the quantity of heat conducted per minute through a duralumin circular disc 119mm diameter and 22.65mm thick when the temperature drop across the thickness of the plate is 9.3°F take the coefficient of thermal conductivity of duralumin as 150 W/m-K. Answer: 22.833 kJ/min
A heating system is to be designed to keep the wings of an aircraft cruising at a velocity of 900 km/h above freezing temperatures during flight at 12,200-m altitude where the standard atmospheric conditions are 55.4°C and 18.8 kPa. Approximating the wing as a cylinder the elliptical cross section whose minor axis is 30 cm and disregarding radiation, determine the average convection heat transfer coefficient on the wing surface and the average rate of heat transfer per unit surface area.
A 30-m-long section of an 8-cm-diameter horizontal hot water pipe passes through a large room whose temperature is 20°C. If the outer surface temperature of the pipe is 70°C, determine the rate of heat loss from the pipe by natural convection. k = 0.02699 W/m °C Pr = 0.7241, ν = 1.749 ×10-5. Select one: a. 3485.4 W b. 3827.7 W c. 2211.8 W d. 2683.6 W
Consider a 2-m-high electric hot-water heater thathas a diameter of 40 cm and maintains the hot water at 55°C.The tank is located in a small room whose average temperatureis 27°C, and the heat transfer coefficients on the innerand outer surfaces of the heater are 50 and 12 W/m2·K,respectively. The tank is placed in another 46-cm-diametersheet metal tank of negligible thickness, and the spacebetween the two tanks is filled with foam insulation (k =0.03 W/m·K). The thermal resistances of the water tank andthe outer thin sheet metal shell are very small and can be neglected. The price of electricity is $0.08/kWh, and the home owner pays $280 a year for water heating. Determine the fraction of the hot-water energy cost of this household that is due to the heat loss from the tank. Hot-water tank insulation kits consisting of 3-cm-thick fiberglass insulation (k = 0.035 W/m·K) large enough to wrap the entire tank are available in the market for about $30. If such an insulation is installed on…
A hot surface at 100°C is to be cooled by attaching3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m·K) to it, with a center-to-center distance of 0.6 cm. Thetemperature of the surrounding medium is 30°C, and the heattransfer coefficient on the surfaces is 35 W/m2·K. Determine therate of heat transfer from the surface for a 1-m * 1-m sectionof the plate. Also determine the overall effectiveness of the fins.
A transformer that is L=20cm long, 6.2 cm wide, and 5 cm high is to becooled by attaching a 10 cm × 6.2 cm wide polished aluminum heatsink (emissivity =0.03) to its top surface. The heat sink has seven fins,which are 5 mm high, 2 mm thick, and 10 cm long. A fan blows air at25°C parallel to the passages between the fins. The heat sink is todissipate 20 W of heat and the base temperature of the heat sink is notto exceed 60°C. Assuming the fins and the base plate to be nearlyisothermal and the radiation heat transfer to be negligible, determinethe minimum free-stream velocity the fan needs to supply to avoidoverheating. (k=0.02681W/m˚C, Pr=0.7248, V= 1.726×10-5 m2/s, )
Convective heat transfer coefficient is 15 W/(m*K), surface area of the fin is 2 m^2, the temperature at the base is 70 C and the ambient temperature is 20 C. Determine the fin efficiency if the actual heat transfer rate from the fin is 500 W? not sufficient information 66 % none of the given 15 % 33 %
A long stainless-steel (AISI 316) steam pipe, with an inside diameter of 6.00 cm and an outside diameter of 8.00 cm, is covered with a layer of asbestos insulation (k = 0.150 W/m-K) 1.00 cm thick, which in turn is covered with foam insulation (k = 0.044 W/m-K) 6.00 cm thick. The inside surface temperature of the stainless-steel steam pipe is measured to be 250.0°C, while the outside surface of the foam is exposed to convection, T_inf = 25.0°C, h_inf = 15.0 W/m^2-K. • Draw and label a sketch of this system. Include dimensions, known temperatures, etc. • Draw and completely label the corresponding 1-D steady-state conduction resistor diagram. • Determine the heat transfer rate through the pipe per unit length. • Calculate the temperature at the asbestos/foam interface.
A hot surface at 100°C is to be cooled by attaching 3-cm-long, 0.25-cm-diameter aluminum pin fins (k = 237 W/m·K) to it, with a center-to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m2 ·K. Determine the rate of heat transfer from the surface for a 1-m x 1-m section of the plate. Also determine the overall effectiveness of the fins.
In a food industry, pieces of meat with approximately 30 cm in diameter and 20 mm in thickness are stored in a industrial freezer and thawed by exposure to ambient air at 15°C with convective heat transfer coefficient equal to 10W/(m2.K). Consider a piece of meat that, when removed from the freezer, had a temperature of -12°C. For defrosting, the piece is hung on a "line", so that both larger surfaces are exposed to the ambient air. For frozen meat, the following properties can be assumed ρ=1090 kg/m3, cp=3.54 kJ/(kg.K), k=0.47 W/(m.K). Ask: (1) Indicating the control volume and the simplifications adopted, obtain the differential energy balance equation for the cooling the piece of meat and describe the conditions of outline and initial that apply to the process, justifying them; (2) Use the appropriate analytical solution to determine the time necessary for the complete defrosting of the part. The part is considered to be completely thawed when a minimum temperature of 5oC is reached…
A person is found dead at 5PM in a room whose temperature is 20°C. Thetemperature of the body is measured to be 25°C when found, Modeling thebody as a 30-cm-diameter, 1.70-m-long cylinder and the heat transfer coefficient estimated to be 8 W/m2·K. and using the lumped system analysis as a rough approximation, estimate the time of death of the person.
/ Hot square plate (1 m ×1 m) is to be cooled by attaching aluminum circular pin fins (D=0.25 cm, L= 3 cm) distributed with distance 0.6 cm as illustrated in Figs.(1-a) & (1-b). If the fin base temperature is 100°C, cooling air temperature is 30°C and h= 35 W/m. °C. Determine the total rate of heat transfer from the finned plate and the effectiveness of the fins? Assume k= 237 W/m.°C and nr=tanh mL/ mL.