43.A 3 mx 3 m square precast reinforced concrete segments to be installed by pushing them through an existing railway embankment for making an underpass as shown in the figure. A reaction arrangement using precast PCC blocks placed on the ground is to be made for the jacks. Radway umbankment Not to Scake RCC segment Jacks Natural Ground 75 At each stage, the jacks are required to apply a force of 1875 kN to push the segment. The jacks will react against the rigid steel plate placed against the reaction arrangement. The footprint area of reaction arrangement on natural ground are: c = 17 kPa; = 25° and y = 18 kN/m³. Assuming that the reaction arrangement has rough interface and has the same properties that of soil, the factor of safety (round off to 1 decimal place) against shear failure

43.A 3 mx 3 m square precast reinforced concrete segments to be installed by pushing them through an existing railway embankment for making an underpass as shown in the figure. A reaction arrangement using precast PCC blocks placed on the ground is to be made for the jacks. Radway umbankment Not to Scake RCC segment Jacks Natural Ground 75 At each stage, the jacks are required to apply a force of 1875 kN to push the segment. The jacks will react against the rigid steel plate placed against the reaction arrangement. The footprint area of reaction arrangement on natural ground are: c = 17 kPa; = 25° and y = 18 kN/m³. Assuming that the reaction arrangement has rough interface and has the same properties that of soil, the factor of safety (round off to 1 decimal place) against shear failure

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.45 La barra rígida ABC está suspendida de tres alambres del mismo material. El área de la sección transversal del alambre en B es igual a la mitad del área de la sección transversal de los alambres en A. Determine la tensión en cada alambre causada por la carga P mostrada.
The post is fixed to the ground and a rectangular pressure of 7 lb/ ft2 acts perpendicular to the face of the signboard. What resultant internal loadings act on the cross-section through point B of the signpost?
2. A reinforced concrete beam having a width of 280 mm and a total depth of 600 mm isreinforced for tension at the bottom with 6 - 36 mmɸ bars placed on two layers, 4 bars onfirst layer and 2 bars on second layer. Compute the effective depth of the beam and theclear horizontal spacing between bars.
econd Year 2 Works: "Strength of Materials" 83 1-54* Three forces are applied along the centerline of a steel bar as shown in Fig. P1-54. Determine the internal forces on transverse cross sections in intervals AB, BC, and CD of the bar. 75 kN 100 kN A gridag B C D 50 kN Prof. Dr. Qais Fadhil Figure P1-54 1-57* Determine the internal forces on section a-a in the angle bracket shown in Fig. P1-57.
Determine the Internal Forces at ALBLGHFGAB in Kn
2. The roof truss shown in Figure is pinned at point A, and supported by a roller at point H. Determine the force in member DG and DF.Use method of sections D 55 kN 45 kN MATHalino.com 2.5 m 1.5 m 1.5 m MATHalino.com H. 2 m C 2 m 2 m 2 m 90 kN MATHalino.com
Determine bar force member EF 10 KN 15 KN 10 KN E 0.9 m 0.9 m A G J B |F 1.2m 1.2m 1.2m
In the given 20.0 meter slab and inclined 10 owith the horizontal, the ends are resting on inclines of 35 degreesincline at B and 25 degrees at A, a semi-trailer truck is to pass through it with the wheel loads as shown. How Far (x, meters) shall be the front wheels located before motion impends, the angle of friction is 18 o for all areas of contact. If the weight of the slab is to be neglected. Use 3 Decimel Places
HiW: find the stresses on the plane 45° Deaws M hor Circle anod locate Op. 120 kPa -45 plane -50 kPa 50 kPa - 30 120 kPa
59. ssm Two metal beams are joined together by four rivets, as the draw- ing indicates. Each rivet has a radius of 5.0 × 10-³ m and is to be exposed to a shearing stress of no more than 5.0 × 10° Pa. What is the maximum tension T that can be applied to each beam, assuming that each rivet carries one-fourth of the total load? -Rivet
The building below is a broncaptering building 120 w6 wi W2 0.50 WA WS W7 W3 0.50 1.50 0.50 Figure 1 Gravity of Front Earth Retaining Wall Vertical Density W Distance Force Wide Height Moment (Ton) (m) (Ton M) W1 0.30 2.5 2.20 1.650 1.85 3.053 W2 1.20 2.5 2.20 3.300 1.30 4.290 W3 2.00 1.0 2.20 4.400 1.00 4.400 W4 0.20 0.5 0.73 0.036 0.57 0.021 W5 0.50 0.5 0.73 0.182 0.25 0.046 W6 0.50 2.0 1.00 1.000 2.25 2.250 W7 0.50 0.5 0.73 0.182 2.25 0.410 10.750 14.468 Land Data - Mass of stone volume (yb ) = 2.2 t/m3 - Soil volume weight (y) = 1.62 t/m3 - Wet soil volume (y') = 0.94 t/m3 - Friction Angle in () = 22° - Soil cohesion (c) = 2.6 t/m2 How can we calculate the density and Height ?
4. If the width of the bedplate is 3m and the clearance is 0.3 what is the upper width of the machine foundation