4800- Vrms transmission line feeds a distribution transformer with 1200 turns on the primary and 28 turns on the secondary . When a 10-Ohm load is connected across the secondary . Find ? a ) the secondary voltage

4800- Vrms transmission line feeds a distribution transformer with 1200 turns on the primary and 28 turns on the secondary . When a 10-Ohm load is connected across the secondary . Find ? a ) the secondary voltage

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.6MCQ: Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is...

See similar textbooks

Related questions

Q: Determine the rms value of waveform depicted in Figure in mA. i(1) (mA) 9 2 3 4 5 6 7 - t(s)

A: Given:A Signal, To find:RMS value of the signal shown in the given waveform.

Q: Consider the following statements with reference to PCM and DPCM systems having same sampling…

A: Consider the following statements with reference to PCM and DPCM systems having the same sampling…

Q: Answer the following: Find the convolution of the two finite-length sequence: 8 x(n) = Σ 2n[u(n) –…

Q: 2) A current of 250mA flows through a perfect inductor, when it is connected to a 5V, 1kHz supply.…

A: The current, The supply voltage, The supply frequency,

Q: (0,^ <07 y[^] =√1,0 <0²11 0, 11 <^ Find the 2-transform of the of convergence 2-transform of the…

A: Given Data:A discrete-time signal of,To Find:Z- Transform of the signal.Region of Convergence (ROC)

Q: Problem 3: For the MOSFET transistor shown in the circuit below, the parameters as follows, V₁ = 1V…

Q: Instructor Problem 2: Given the continuous time unit step function u(t), provide sketches for each…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 1. Implement the given Boolean function in (a) NOR and (b) NAND gates only. Use two-input gates…

A: The given Boolean function is,

Q: Please explain the difference (in assumptions and when you use them in practice) between the BIS,…

A: The BIS (Best Interest of Society), SPE (Social Planner's Efficiency), and WSE (Welfare-Social…

Q: b) Referring to the circuit shown in Figure 1, determine the time-function of the voltage u(t)…

A: In this questionWe need to determine the voltage across the capacitor. We knowCapacitor act as open…

Q: a. What is the significance of the name IIR in the IIR filter? b. How negative feedback is more…

A: It is asked to explain the significance of the names of IIR in the IIR filter.

Q: 2. Based on the double diode partial limiter and using a simplified diode model: Tabulate the input…

Q: your RSP is complete it will include Reg. F (8 bits), Reg. G (8 bits), the Switch Input (8 bits),…

A: To determine the number of test patterns required for exhaustive testing, we need to calculate the…

Q: Derslerim/ Ceşitli / MÜHENDISLIK FAKÜLTESI / Elektrik-Elektronik Mühendisliği (%30 ing.) /…

A: Step-1->

Q: Q5 [3-45] Write the AHDL code that will produce the following output functions: X = A + B Y = AB Z =…

A: AHDL (Altera Hardware Description Language) is a proprietary hardware description language developed…

Q: A 3-phase, 50-Hz transformer has a star-connected primary and delta-connected secondary, the line…

A: Given data:Primary side: Star connected.Secondary side: Delta connected.Primary side line voltage,…

Q: f(x)=9x-8 Simplify vour answer as much as possible.

A: f(x)=9x-8 Simplify your answer as much as possible.We need to simply f(x) = 9x-8

Q: The power spectral density of a real process X(t) for positive frequencies is shown below. The…

A: The power spectral density,

Q: Determine the inductor current i(t) for t20. Given that Vs1 =9V, Vs2 = 12V, L= 120mH, R₁ = 2.29, R₂…

Q: Power has a dark side.” Comment and providing examples

A: It is asked to discuss with supporting explanations about the dark sides of electric power.

Q: For the circuit of Figure, assume the source operates at a frequency of 100 rad/s. Calculate the…

A: Average Power delivered to 100ohm resistor for the given Circuit.

Q: At T = 300 K, the band gap and the intrinsic carrier concentration of GaAs are 1.42 eV and 106 cm-3,…

Q: Consider a bandpass filter of the form: Half) O / -fo -fe-fi-fe² fi 2 / fo fe+fL The equivalent…

A: Given:Frequency response of bandpass filter :Low pass filter is made from the band-pass filter :To…

Q: -Calculate the average power of the discrete-time wave shown in fig a? * ******* O-1 O 1 06 O O…

A: We need to find the average power of this given signal

Q: 2) A current of 250mA flows through a perfect inductor, when it is connected to a 5V, 1kHz supply.…

A: It is given that:

Q: Implementing F= (A + B)(C+ D)E A' B A B' C D' F

A: Given logic circuit:Aim: To write a Verilog gate-level description of the circuit

Q: Assuming an operating frequency of 40 rad/s for the circuit shown in Figure, and a load impedance of…

Q: 2- Analyze given sequential circuits and write truth table, draw state diagram. X CLK Day KQ K Q A B

Q: 25. A synchronous generator is connected to an infinite bus with excitation voltage E, = 1.3 pu. The…

A: It is given that:

Q: Given a 76sqm residential unit to be provided with 230V, single phase power supply with the ff…

A: It refers to the total amount of electrical power required by all the devices and appliances…

Q: 1/4 of a circle of radius R carrying current i is given in the figure. What is the magnetic field at…

Q: Calculate the voltage gain of the following circuit. Assume that the capacitors are very large and X…

Q: The button is on the 3rd bit of PORTC. When the button is pressed, turn on all leds on PORTD. ORG…

A: Microcontroller (PIC16F877A):…

Q: For the circuit of Figure, assume the source operates at a frequency of 100 rad/s. Calculate the…

A: In this questionWe need to determine the power in 100 ohm resistance.We are solving this problem…

Q: 6. A hall is to be provided with a lighting installation. The hall is 30- mx 20 m x 8 m (high). The…

A: A lighting installation is to be provided for the hall.Area of the hall, Illumination, Utilization…

Q: In the figure below, imagine an ammeter inserted into a line containing R_3. a) What will you read…

A: In this questionWe need to determine the reading of the ammeter. We are solving this problem using…

Q: For the give circuit below a) What is the Laplace transformation b) What is the transfer function c)…

Q: Find the [a] average power absorbed by the 0.6-kV resistor of Figure in mW. 0.6 ΚΩ www 1.8 ΚΩ 4 √5…

Q: Calculate the input impedance for the circuit shown in figure. Assume λ = 0. Şekildeki devre için…

A: For the given circuit the value of input impedance needs to be calculated and the same can be…

Q: For the series diode configuration of Fig. 2.16, determine VD, VR, and ID-

A: It is given that:

Q: 7. A 3 MVA, 6 pole alternator runs at 1000 rpm on 3.3 kVolt bus-bars. The synchronous reactance is…

Q: Consider a separately excited DC generator rated at a field voltage of 430 V, an armature current of…

A: Consider a separately excited DC generator rated at a field voltage of , an armature current of ,…

Q: from the route table, determine the roots found in the left-half plane, right half plane and…

Q: A generator having 75 as its internal resistance operating at 1 Hertz and feeds to 100 load through…

Q: EXAMPLE 8.14 For the astable multivibrator using the op-amp shown in Fig. 8.67, R = 10 k2, C = 0.01…

A: Given :Find :=> Here Find time period of the output square wave with range of R(2).

Q: In what ways can you safeguard your machine against power outages and other calamities?

A: In what ways can you safeguard your machine against power outages and other calamities?

Q: Assuming an operating frequency of 40 rad/s for the circuit shown in Figure, and a load impedance of…

A: For the given circuit the value of apparent power delivered to the load in VA needs to be calculated…

Q: A two-legged core is shown in Fig. Q5. The winding on the left leg of the core (N₁) has 600 turns,…

A: Given that:N1=600N2=200i1=0.5 Ai2=1 Aμr=1000To determine:Total flux in the core

Q: Ib,Ic,Ie?????????

A: It is given that:

Q: For the circuit of Figure, find the apparent power delivered to Zc if ZA= 5-12 12, ZB = 30, Zc = 8 +…

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

A 4800- V_rmstransmission line feeds a distribution transformer with 1200 turns on the primary and 28 turns on the secondary . When a 10-Ohm load is connected across the secondary . Find ?

a ) the secondary voltage

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation of V2(secondary voltage)

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer at the load end of a 2400-volt feeder whose series impedance is (1.0+j2.0) ohm. The equivalent series impedance of the transformer is (1.0+j2.5) ohms referred to the high-voltage (primary) side. The transformer is delivering rated load at a 0.8 power factor lagging and at a rated secondary voltage. Neglecting the transformer exciting current, determine (a) the voltage at the transformer primary terminals, (b) the voltage at the sending end of the feeder, and (c) the real and reactive power delivered to the sending end of the feeder.
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
An ideal transformer has no real or reactive power loss. (a) True (b) False
The motors M1andM2 of Problem 3.45 have inputs of 120 and 60 MW, respectively, at 13.2 kV, and both operate at unity power factor. Determine the generator terminal voltage and voltage regulation of the line. Neglect transformer phase shifts.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
An open-delta three-phase transformer system has one transformer center-tapped to provide a neutral for single-phase voltages. If the voltage from line to center tap is 277 V, what is the high-leg voltage?
Given the transformer circuit below, a load of 2.5cis20° Ohms is connected to the output terminals of the transformer. If the voltage across the load is 230V, determine the following:a. ILb. IMc. ICd. Source voltage, V