5 7 9. -1 8. A = 1 9. -1 -5 6 4 -7 3 -2 -3 0 8 Solve for the determinant of A. 63 3 7

Q: 8 m -5m 4 m 5 m 5 m 15 m 500 N In connection with the above figure, as an Engineer you have to repla...

A:

Q: find femperature, at the trißle point? Vapou pressure of liquid & Sofid ammoniay are respectivelcy g...

A: Write the expression for vapour pressure of liquid ammonia. lnP=14.15-3054T      ...... (1) Write th...

Q: 4. A 1.00 mole sample of a monatomic ideal gas, originally at a pressure of 1.00 atm, undergoes a th...

A:

Q: The equation of motion of a particle is s = 8t2 + 3t – 10, where s is in meters and t in seconds. Fi...

A:

Q: Example 7. Knowing that at the instant shown block A has a velocity of 2 ft/s to the left and an acc...

A:

Q: The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction. Gear...

A:

Q: A bar of a steel alloy that exhibits the stress–strain behavior shown in Animated Figure 7.34 is sub...

A: Given data: Specimen length = 375 mm = 0.375 mCross section = 5.5 x 5.5 mm2 = 30.25 mm2 

Q: modulus of ln (2 +3 j)?

A:

Q: 10 Ibm/min of Steam at 4.5 MPa with a moisture content of 7% undergoes a constant volume process unt...

A:

Q: hat is the resulting angle in radian with 2 decimal places if the complex number is 1+3

A: Given:z=1+3j

Q: Humidity ratio of the air is?

A: Need to find humidity ratio of air.

Q: 3.) The bent rod is supported at A, B, and C by smooth bearings. The bearing are perfectly aligned a...

A: Given data, Coordinates of A = (2, 0, 0) Coordinates of B = (0, 0, 1) Coordinates of C = (0, 1, 3) T...

Q: 3. Compute all the bar forces, indicate if the members are in tension or compression. Length are in ...

A: GIVEN DATA - A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN ALL BARS CONCEPT USED - METHOD OF JOINTS

Q: Cantilever steel shaft is loaded by concentrated couples. M1 M2 OM3 d Given: 14-21; 1z=1,21; 13=1,51...

A:

Q: Consider a vehicle moving at a velocity of 1,000 mps through air and hydrogen. The specific gas cons...

A:

Q: When designing patterns for casting, patternmakers use special rulers that automatically incorporate...

A:

Q: A 2411 Ib car is moving up a 7 degree incline as shown. Determine how many seconds will it take for ...

A:

Q: This question requires the use of the extracts from the tables of thermodynamic properties supplied....

A:

Q: find frmperature at the trißle point ? Vapow pressure of.liquid & Sofid ammoni ay are respecfivelcy ...

A:

Q: the dimension (in mm) of cross section from strength calculation            a = ?

A: allowable stress = yield stress/ FOS = 240/2 = 120 MPa well evaluate bending stress.

Q: Pressure remains constant at 689.5 kPa while the volume changes from 0.567 m3 to 0.283 m3. Find the ...

A: Dear student,                    According to the guidelines I am allowed to answer only three sub-p...

Q: The turning moment diagram of a quadruple expansion marine engine (multi cylinder engine) drawn to t...

A:

Q: installation. Overpressure in chamber A, from which water outflows by nozzles B, is ppA = 80 kPa. Ve...

A:

Q: A heat engine produces 200 kJ/s of mechanical power and operates at an efficiency of 10%. What would...

A: Given Data W=200 kJ/s Efficiency=10%

Q: Riser is designed so as to ?

A: Riser is part of gating system in casting process. The gating system includes pour basing, sprew, sp...

Q: 4-5. Determine the moment about point B of each of the three forces acting on the beam. Probs. 4-4/5...

A:

Q: Calculated Measured Calculated Percent Table 3 Velocity (m/s) Pressure (kPa) Pressure (kPa) Differen...

A: Since you have asked multiple questions, we will solve the first question for you. If you want any s...

Q: Ex: A mass of 500g is hung on a spring and causes it to have a period of 1.5 s. What is the spring c...

A: Given, Mass hung on the spring = m = 500 g = 0.5 kg Time period of oscillations = T = 1.5 s   From t...

Q: Determine the internal normal force, shear force, and bending moment at point C in the beam.

A:

Q: A body hangs from a spring balance supported from the roof of an elevator. If the elevator has an up...

A: Given   Weight, m = 45 lb   Acceleration, a = 4 ft/s2 Find  True weight of the body

Q: A cylindrical specimen of a brass alloy having a length of 104 mm (4.094 in.) must elongate only 5.2...

A: Given data: L0=104 mmF=95000 N∆L=5.2 mm Need to determine the radius of the specimen.

Q: l = 1.95 mm.    w= 1.89 mm.    h= 5.82 m.  Coordinates for Point A is A(2,2,2)m Coordinates for Po...

A: As per the guidelines, I can solve only first three subparts. For rest parts, repost in a separate p...

Q: This question requires the use of the extracts from the tables of thermodynamic properties supplied....

A:

Q: A vacuum gauge mounted on a condenser reads 660 mmHg. What is the absolute pressure in the condenser...

A:

Q: 1. A rigid member CBD is supported by a flexible cable AB as shown below. If a force applied to the ...

A:

Q: . The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal befo...

A: Given:La=2 ftAa=0.4 in2Lb=3 ftAb=0.2 in2

Q: ‘Hydraulic lift’ works on the basis of

A:

Q: Consider a vehicle moving at a velocity of 1,000 mps through air and hydrogen. The specific gas cons...

A:

Q: 5. In the beam loaded as shown in the figure, compute the magnitude, /"direction and position of the...

A:

Q: The plate in the figure has cross-sectional area A and is subjected to the axial load P. Determine t...

A:

Q: 7. At the beginning of compression in an ideal air standard Diesel cycle, the = 100 kPa and T= 300K....

A: As per the guidelines of BARTLEBY we are subjected to solve only 3 sub parts at a time. Please repos...

Q: P3.48 The small boat is driven at steady speed Vo by compressed air issuing from a 3-cm-diameter hol...

A:

Q: Calculate its mass ratio R, payload ratio P,

A: Mass Ratio, R = Final MassInitial Mass=m1m0=200002500=8 Payload Ratio, P = Payload MassInitial Mass

Q: A ame etenmant is gabjecfed fo the foleing biraxial of strex: Ox-75 mpa - 15 mpa %3D てx35m sheap sfz...

A: Given:σx=75 MPaσy=15 MPaζxy=35 MPaζ=95 MPa

Q: 43.A cylindrical steel shaft 100 mm in diameter and 2 m long subjected to a censile load of 25 kN, w...

A: Given   Diameter, d = 100 mm                          Length, L = 2 m                            Loa...

Q: A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment...

A: If just two forces act on a balanced body, they must be of equal size, co-linear, and opposing in di...

Q: Figure shows an airplane moving horizontally with a constant velocity of +100 m/s at an ,-100 mis al...

A: All the values are calculated using equation of motion, for calculating the value of time, we applie...

Q: A closed, isolated system is in equilibrium. Which of the following statements will NOT be true? O a...

A:

Q: The gas constant R has the value 287 J/Kg * K for dry air. Using the ideal gas law (P = PdryRT): Fin...

A:

Q: It is proposed to modify the heat engine in Q8 in such a way that it will now require exactly 200 kJ...

A: Given that the energy supplied to the Q8 engine is

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.