(5) A homogeneous 800-kg bar AB is supported at either end by acable as shown in the figure. Calculate the smallest area ofeach cable if the stress is not to exceed 90 MPa in bronze andBronzeSteelL= 3 mL= 4 m120MPa in steel.10 m

Answered: Image /qna-images/answer/212b22a6-25e2-4200-800c-bc409a592a09.jpg

(5) A homogeneous 800-kg bar AB is supported at either end by a cable as shown in the figure. Calculate the smallest area of Bronze L=4 m Steel L= 3m each cable if the stress is not to exceed 90 MPa in bronze and 120 MPa in steel. 10 m

(5) A homogeneous 800-kg bar AB is supported at either end by a cable as shown in the figure. Calculate the smallest area of Bronze L=4 m Steel L= 3m each cable if the stress is not to exceed 90 MPa in bronze and 120 MPa in steel. 10 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.6.10P: A prismatic bar with a length L = 1 m and cross-sectional area A = 1200 mm2 is supported at the...

See similar textbooks

Similar questions

,10-6 A prismatic bar with a diameter d0= 20 mm is being compared with a stepped bar of the same diameter(d| = 20 mm) that is enlarged in the middle region lo a diameter d2= 25 mm (see figure). The radius of the fillets in the stepped bar is 2.0 mm. (a) Does enlarging the bar in the middle region make it stronger than the prismatic bar? Demonstrate your answer by determining the maximum permissible load for the prismatic bar and the maximum permissible load F, for the enlarged bar, assuming that the allowable stress for the material is 80 MPa. (b) What should be the diameter d0of the prismatic bar if it is to have the same maximum permissible load as does the stepped bar?
A long, rectangular copper bar under a tensile load P hangs from a pin that is supported by two steel posts (see figure). The copper bar has a length of 2.0 m, a cross-sectional area of4S00 mm", and a modulus of elasticity Ec= 120 GPa. Each steel post has a height of 0.5 m, a cross-sectional area of 4500 mm2, and a modulus of elasticity E = 200 GRa. (a) Determine the downward displacement
A plastic bar of rectangular cross section (ft = 1.5 in. and h = 3 in.) fits snugly between rigid supporls at room temperature (68oF) but with no initial stress (see Figure). When the temperature of the bar is raised to 160oF, the compressive stress on an inclined plane pq at mid-span becomes 1700 psi. (a) What is the shear stress on plane pq? (Assume a = 60 × 10-6/*t and E = 450 × 103psi.) (b) Draw a stress element oriented to plane pq and show the stresses acting on all laces of this element. (c) If the allowable normal stress is 3400 psi and the allowable shear stress is 1650 psi. what is the maximum load P (in the positive x direction), which can be added at the quarter point (in addition to thermal effects given) without exceeding allowable stress values in the bar?
The wide-flange, pinned-end column shown in the figure carries two loads: a force P1= 450 kN acting at the centroid and a force P2= 270 kN acting at a distance s = 100 mm from the centroid. The column is a W250 x 67 shape with L = 4.2 m, E = 200 GPa, and y= 290 MPa. What is the maximum compressive stress in the column? If the load P1remains at 450 kN, what is the largest permissible value of the load P2in order to maintain a factor of safety of 2.0 with respect to yielding?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A curved bar ABC having a circular axis (radius r = 12 in.) is loaded by forces P = 400 lb (see figure). The cross section of the bar is rectangular with height h and thickness t. If the allowable tensile stress in the bar is 12,000 psi and the height A = 1.25 in., what is the minimum required thickness rmax?
Truss members supporting a roof are connected to a 26-mm-thick gusset plate by a 22-mm diameter pin, as shown in the figure and photo. The two end plates on the truss members are each 14 mm thick. (a) If the load P = 80 kN, what is the largest bearing stress acting on the pin? (b) If the ultimate shear stress for the pin is 190 MPa, what force Pult is required to cause the pin to fail in shear? Disregard friction between the plates.
A hollow circular tube T of a length L = 15 in. is uniformly compressed by a force P acting through a rigid plate (see figure). The outside and inside diameters of the tube are 3.0 and 2.75 in., respectively. A concentric solid circular bar B of 1.5 in. diameter is mounted inside the lube. When no load is present, there is a clearance c = 0.0I0 in. between the bar B and the rigid plate. Both bar and tube are made of steel having an c[autoplastic stress-strain diagram with E = 29 X LO3 ksi and err= 36 ksi. (a) Determine the yield load Pt- and the corresponding shortening 3yof the lube. (b) Determine the plastic load Ppand the corresponding shortening Spof the tube. (c) Construct a load-displacement diagram showing the load Pas ordinate and the shortening 5 of the tube as abscissa. Hint: The load-displacement diagram is not a single straight line in the region 0 ^ P ^ Pr
A copper bar of rectangular cross section (b = 18 mm and k = 40 mm) is held snugly (but without any initial stress) between rigid supports (see figure). The allowable stresses on the inclined plane pq at mid-span, for which ?? = 55°. are specified as 60 MPa in compression and 30 MPa in shear. (a) What is the maximum permissible temperature rise AT if the allowable stresses on plane pq are not to be exceeded? (Assume a = 17 × 10-6/oC and E = 120 GPa.) (b) If the temperature increases by the maximum permissible amount, what are the stresses on plane pq? (c) If the temperature rises AT = 2SoC how far to the right of end A (distance BL, which is expressed as a fraction of length L) can load P = 15 kN be applied without exceeding allowable stress values in the bar? Assume that a =75 MPa and t = 35 MPa.
A stepped bar ACB with circular cross sections is held between rigid supports and loaded by an axial force P at midlength (see figure). The diameters for the two parts of the bar are d1= 20 ram and d2= 25 mm, and the material is elastoplastic with yield stress s = 250 MPs. Determine the plastic load Pp.
An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The thickness of the wall of the tube is 0.25 in. (a) What is the minimum required outer diameter d minif the allowable tensile stress is 12.000 psi? (b) Repeat part (a) if the tube has a hole of a diameter J/10 at mid-length (see figure parts b and C).
A steel bar with a diameter d = 12 mm is subjected to a tensile load P = 9.5 kN (see figure). (a) What is the maximum normal stresser smax in the bar? (b) What is the maximum shear stress tmax? (c) Draw a stress element oriented at 45° to the axis of the bar and show all stresses acting on the faces of this element. (d) Repeat part (c) for a stress element oriented at 22.5° to the axis of the bar.