5- Find the pulse width for a monostable timer if R= 100KQ and C= 100μF?

Q: A one-shot is a type of(a) monostable multivibrator (b) astable multivibrator(c) timer (d) answers…

A: Answer: A one-shot is also known as a monostable multivibrator. It has one stable state.

Q: Given the 8MHz oscillator, the timer is set to 8 bits with Prescaler 2 and preload

A: Given that frequency of oscillator (f) = 8 MHz = 8 * 10⁶ Hz Here the timer used is 8 bits. Hence the…

Q: Design a 1-minute timer using a 60 Hz power line as an interrupting source. The output ports should…

A: Flow Diagram:

Q: Create a one-shot using a 555 timer that will produce a 0.5s output pulse

A:

Q: The process of adressing each input during one clock pulse is called

A: According to the Question we need to identify that" The process of addressing each input during one…

Q: 3. You are controlling an angle type, servo motor which moves from -90 to +90 degrees. The period of…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: Consider the following T flip flop timing diagram: What type of clock trigger is used? Clk

A: When clock is at rising edge and T is 1 and Q is alter at that time

Q: Consider the following T flip flop timing diagram: What type of clock trigger is used?

A: Correct answer is option A. Rising Edge Trigger

Q: What is the purpose of the prescaler in microcontroller timers? Select the clock source for a timer.…

A: Given To the purpose of the Prescaler in microcontroller timer.

Q: With a counter 10 lights will be controlled. At the first clock pulse all lights will be ON (1). at…

A: The ten lights can be considered as a, b, c, d, e, f, g, h, i and j. All the lights will be in ON…

Q: a monostable multivibrator using 555 timer with an unstable state which is 10 ms long. If the…

A: Monostable Multivibrator Using 555 Timer: We have seen that multivibrator and CMOS Osillators can be…

Q: Write a Test Bench for the Five-Cycles High Laser Timer (please see the VHDL code for reference).

A: Solution:--   1)The given question has requested for the solution which is to be provided in the…

Q: A positive-going pulse is applied to an inverter. The time interval from the leading edge of the…

A: A positive-going pulse implies a pulse going from LOW to HIGH. So, input goes LOW to HIGH whereas…

Q: Design an embedded C code, based on STM32F100RB microcontroller, for blinking two LEDs connected…

A: 8051 Microcontroller is a programmable device which is used for controlling purpose.Basically 8051…

Q: RB4 is connected to a pulse generator and pin RB1 is connected to a led, write a program to toggle…

A: Solution:--   1)As given in the question it is required for the program that is related with     the…

Q: In 555 timer ,if vcc=51, the lower comparator triggers when the trigger input(pin2) voltage reaches…

A: Lets see the solution.

Q: Discuss two modes of 555 timer with circuit diagram and proper equations. Provide two applications…

A: Astable mode of 555 Timer is also called as free-running or Self-triggering mode as it doesn't…

Q: ed to include timers in our rd

A: RDT protocols Reliable data transfer protocols (RDT, RDP) are algorithmic procedures that provide…

Q: How are 556 and 7555 timers different from the basic 555 timer?

A: 555 Timers 555 clock IC is an incorporated circuit utilized in an assortment of utilizations like…

Q: 7. For the pulse shown in Figure 1–60, graphically determine the following: (a) rise time (b) fall…

A: Given: 7. For the pulse shown in Figure 1–60, graphically determine the following:(a) rise time (b)…

Q: A flip-flop changes its state during the(a) complete operational cycle(b) falling edge of the clock…

A: GIVEN: A flip-flop changes its state during the(a) complete operational cycle(b) falling edge of the…

Q: The throughput of a flash ADC is measured in(a) displacement per second (b) distance per second(c)…

A: Given: The throughput of a flash ADC is measured in(a) displacement per second (b) distance per…

Q: TE and OUT signals for Mode 1, Mode 2 mmable counter for the given CLOCK an

A: Q.

Q: 8051 microcontroller C program to toggle only pin P1.3 continuously every 250 ms. Use timer 0, mode…

A: 8051 microcontroller has two independent timer which can be used as timer(to generate…

Q: For the following inputs, the selector digits of the given multiplexer circuit should be (s1,s0)=( )…

A: We are given 4x1 multiplexer and values of 4 inputs ( I0 to I3). As we know that output Y select an…

Q: Calculate the conversion time when the clock frequency is changed to 1MHz

A: n=8 clock frequency = 2 MHz VT = 0.1mV FS = 5.12V

Q: th an aid of timing diagram, show your work on how you detemine the sequence of the inter in Figure…

A: All the flip-flop are connected to same clock. So on same clock, output of all flip-flop will…

Q: Assume that XTAL = 11.0592 MHz. What value do we need to load the timer's register if we want to…

A: It is given  that  XTAL = 11.0592 MHz and  the counter will counts up every 1.085 us. It will say…

Q: (1) 1. Given the input waveforms shown below, sketch the output Q of an SR latch. S R

A:

Q: JK Flip-flop a. Mount the 7476 IC on your breadboard. Connect the power and ground terminals of the…

A: A flip failure transfer circuit chips away at a bistable circuit idea where it has two stable stages…

Q: Consider the following T flip flop timing diagram: What type of clock trigger is used? Clk T. Q

A: In T Flip Flops we know that it toggles the output when provided with a positive input. In the given…

Q: tocols have timers, so why do we ne

A: Our rdt protocols have timers, so why do we need them?

Q: 5400 TTL series IC's can operate over a temperature range of ( -55 to 125 ° C ) . Select one : O…

A: 5400 series predated the much more common 7400 family by a couple of years. The main difference…

Q: 5400 TTL series IC's can operate over a temperature range of ( -55 to 125°C). Select one: O True O…

A: 5400 TTL series IC's can operate over a temperature range of ( -55 to 125°C) is:

Q: In a three-stage space division switch, the parameters are N = 300, n=10 and k =5. The number of…

A: The multistage switch, which merges crossbar switches in numerous (usually three) stages, is a…

Q: Find the resistor value to create a timer for 100 second using 0.002 F CapacitorMulti Line Text.

A: var seconds_inputs =  document.getElementsByClassName('deal_left_seconds');     var total_timers =…

Q: 3. Complete the truth table for the switch level circuit below. If a floating or shorted output is…

A: The switch level of modeling provides a level of abstraction between the logic and analog-transistor…

Q: Consider the positive edge triggered sequential circuit shown below. Fill in the waveforn for output…

A: Actually, sequential circuit contains set of inputs and outputs.

Q: A pulse waveform with a frequency of 20 kHz is applied to the input of a counter. During 40 ms, how…

A: Given:   A pulse waveform with a frequency of 20 kHz is applied to the input of a counter. During 40…

Q: In synchronous counter ,the clock pulses are given simultaneously. Select one: True False

A: Synchronous counter uses clock pulses at each interval of time.

Q: Given: In a Laser Circuit FSM, the output x equals 25 nanoseconds, and Tclk equals 5 nanoseconds.…

A:

Q: Write python code for a "Count down clock and timer" Explain how the c

A: Required: Write python code for a "Count down clock and timer" Explain how the code works

Q: erive the 8-QAM output using the transmitter block diagram in the module of the following input: (a)…

A: : QAM is a combination of PSK & ASK                 PSK + ASK = QAM : To Make 8- QAM take 2…

Q: Clock Complete the timing diagram for the Timput to a negative-edge triggered T fip-flop. Clock

A: Truth table for D truth table for T flip flop T flip flip means toggle Truth table for JK

Q: Read numbers N and M from Serial monitor and make LED on pin 13 blink N times with an interval of M…

A: Blinking N times: The "Scheduler" library allows the Arduino to manage the multiple tasks at the…

Q: The value of the rise time tr is: O 0.1 sec 0.392 sec O O O

A: .192 sec

Q: A noise gate is a limiter that allows a signal to pass through only when it is above a set…

A: Yes it is true that A noise gate is a limiter that allows a signal to pass through only when it is…

Q: select one: a) An asynchronous reset. b) A D type flip-flop. c) A clock. d) A synchronous reset.

A: If we have only Clock in the sensitivity list and reset in the body , then the reset happens only at…

Q: the synchronous counters different from the asynchronous counters by less propagation operate in a…

A: Answer : Synchronous counter is faster than asynchronous counter. synchronous counter , flip flop…

Q: A folded dipole has a wider bandwidth than a simple dipole. Select one: True False

A: Solution: