5. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a 1.5-kg triangular plate to form the composite thin plate as shown. Which of the following best approximates the gyradius of the thin plate with respect to y-axis? r = 0.20 m 0.1388 m 0.0903 m 0.00815 m 0.01926 m 0.20 m y 0.40 m x 0.20 m

5. A 1.2 kg quarter circular plate with 0.20 m radius is welded to a 1.5-kg triangular plate to form the composite thin plate as shown. Which of the following best approximates the gyradius of the thin plate with respect to y-axis? r = 0.20 m 0.1388 m 0.0903 m 0.00815 m 0.01926 m 0.20 m y 0.40 m x 0.20 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.75P

See similar textbooks

Similar questions

Please evaluate the shape factor and answer part c)
A 37.5-mm-diameter rod 6 mlong elongates 12 mm under a load 236 KN. Thediameter of the rod decreases 0.025 mm during theloading. Determine the following properties of thematerial: (a) Poisson’s ratio.(b) Young’s modulus(c) The modulus of rigidity.
Is the frame determinate or indeterminate? Support your answer.
4 A frustum of a cone 72 mm diameter of circular base, 48 mm diameter of top and having anaxis of 72 mm length has a hole of 30 mm diameter drilled centrally through its flat faces.The frustum rests on the rim of its base in such a way that the base makes an angle of 45° toHP and the axis is in a vertical plane parallel to VP. Draw its elevation and plan
The rod BD is made of material with G1= 33 GPa has a diameter 46 mm is bonded to the tube CA at point B, the tube made of material with G2=56 GPa has an outer diameter 97 mm and wall thickness of 8 mm. If T1=1268 N.m and T2=2282 N.m, answer the following questions: The polar moment of inertia of the rod BD is The polar moment of inertia of the tube CA is The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is The angle of twist between C and B is The reaction at point A is
A shaft is rotating as part of an aircraft compressor. A disc is located midwayalong the rigid shaft that is L=1.8m long in total as shown in Fig. Q4. The discalso lies midway between two supporting bearings that are LB=1.4m apart. Thedisc has a mass of MB=100kg and the centre of mass of the disc is locatedrB=12mm from the axis of the shaft. A mass is added at each end of the shaft.The first has mass MA=40kg and eccentricity rA=37.5mm, whilst the second hasmass MC=30kg and eccentricity rC=40mm. If the system is in static balance:(a) Group the required information in an appropriate table and construct theforce polygon of the rotating system. (b) Determine the angles A and C which ensure the shaft is in staticbalance.(c) Construct the moment polygon for the rotating system and determine the out-of-balance moment when the shaft rotates at ω=100rev/min.
A steel wire of length 1 m and diameter 0.2 mm is elongated by 1 mm due to a weight of 3.14 kg. Determine Young's odulus of steel wire (g=9.8 m/s2)
Two cylinders of diameter 1 m and one cylinder of diameter 2 m are placed symmetrically in a pit 3 m wide (2 m cylinder on top). Find all the contact tones (Surfaces are smooth). Weight of 1 m diameter cylinder = 150 N, weight of 2 diameter cylinder = 240 N
A cylinder has a conical cavity and is topped by a hemispherical cylinder, such as as indicated in the figure. a) Locate the centroid of the composite volume if R = 200 mm and h = 250 mm. b) Locate the center of mass of the composite volume if the cylinder is made of brass (ρ = 8750 kg / mᶟ) and the finish is made of aluminum (ρ = 2770 kg / mᶟ)
A square high-density polyethylene [α = 158×10–6/°C] plate has a width of 205 mm. A 123 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 45°C, determine: (a) the change in width of the plate. (b) the change in diameter of the hole.
Carry out the analysis of a thin cylinder to estimate maximum thickness of cylindrical wall against following data. X=23.89
A square high-density polyethylene [α = 158 × 10–6/°C] plate has a width of 450 mm. A 270 mm diameter circular hole is located at the center of the plate. If the temperature of the plate increases by 46°C, determine:(a) the change in width of the plate.(b) the change in diameter of the hole.