5. Design a circuit using two op amps, to perform the following operation: vo = vị + v2 – 2v3 Now, choose the values of the feedback resistors and the input resistors such that for a maximum output of "X" V the current in the feedback resistor is 0.5mA. [Note that, X = summation of last 3 digits of your ID ]

5. Design a circuit using two op amps, to perform the following operation: vo = vị + v2 – 2v3 Now, choose the values of the feedback resistors and the input resistors such that for a maximum output of "X" V the current in the feedback resistor is 0.5mA. [Note that, X = summation of last 3 digits of your ID ]

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

The op amp in the adder-subtractor circuit attached is ideal. A. Find the output voltage v0 given Va = 2V, Vb = 3V, Vc = 5v, Vd = 6V. B. For the values given in A, find V0 if the feedback resistor is replaced with a 100 ohm resistor.
1.Design a noninverting amplifier (as shown) with a gain of 6, using a 75 kΩ resistor in the feedback path. Draw your final circuit daigram. 2.Suppose you wish to amplify input signals in the range −2.5 V≤vg≤1.5 V. What are the minimum values of the power supplies that will keep the op amp in its linear operating region?
Question 7 For an op-amp amplifier circuit has a closed-loop voltagegain of 5. If the op-amp used has a gain-bandwidth productof 1.5 MHz, and we can only tolerate 10% drop in gain, whatwill be the maximum usable frequency? (help me do this question with explanation)
Based on the simulation’s results, explain the function of a differential amplifier. (Hints: comment on the shape of Vo1 and Vo2, explain what would happen if V1 and V2 were the same, reflect on why it is important that an ideal op-amp has infinite input impedance).
An op-amp with an open-loop gain of 6x105 and Vcc = 15 V has an output voltage of 3 Volts. If the inverting-input voltage is -1.8 microVolts then determine the non-inverting input voltage in microVolts to the single digit decimal place. Do not enter units. For example, if you calculate 3.1x10-6 Volts as your answer then enter 3.1. Similarly, if you calculate 1.872 x10-5 Volts as your answer then enter 18.7 (since this is 18.7 microvolts).
An op amp has Rid = 500 kΩ, Ro = 35 Ω, and A =5×104. You must decide if a single-stage ampliﬁer can be built that meets all of the speciﬁcations below. (a) Which conﬁguration (inverting or noninverting) must be used and why? (b) Assume that the gain speciﬁcation must be met and show which of the other speciﬁcations can or cannot be met. |Av| = 200 Rin ≥ 2×108 Ω Rout ≤ 0.2 Ω
An op amp, with the parameters indicated below, is used in a feedback configu-ration as shown. If the input voltage is Vin=14.5 mV, what is Vout? A = 562 kV/V •Vofs = 22.5 mV •VR = +15 V, -15 V Please answer in typing format solution please
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792
If an inverting amplifier takes input supply voltage of 20V, input resistance and feedback resistance are 15 ohm and 60 ohm respectively then find its output voltage. NOTE : KINDLY ELABORATE BRIEFLY
An op-amp with an open-loop gain of 3x106 and Vcc = 12 V has an inverting-input voltage of 6.7 microVolts and a non-inverting input voltage of 5.4 microVolts. What is its output voltage? Be sure to round your answer to the nearest single digital decimal place. Do not enter units. As an example, if you calculate 7.39 Volts then enter 7.4 as your submitted answer
1. The virtual short is applicable A. If one of the input is tied to the ground B. Only if there is a feedback C. All the time D. Depending on the components used 2. What ideal characteristic of Op-Amp contributes to the Virtual Short concept? A. Zero Ohm Input Resistance B. Zero Ohm Output Resistance C. Input terminals do not let current to flow D. Infinite gain 3. Op-amp closed loop gain varies A. True B. Depending on the resistor values used C. Not applicable D. False
1. Design an inverting-summing amplifier using a 120 kΩ resistor in the feedback path so that vo=-(8va+5vb+12vc). Use ±15 V power supplies. 2.Suppose va=2 V and vc=-1 V. What range of values for vb will keep the op amp in its linear operating region?