5. Determine if the flexural stress of the chocolate will increase or decrease if changes are made in the chocolate's dimensions. Show solution. Initial Dimensions: Lo, To, Wo Flexural stress increase or decrease Dimension Change e.g. L = 2Lo Increase 1. W = 3W. 2. T= 0.5To 3. T= 2To, W =0.25W. 4. L=0.6Lo, W=0.3W. 5. L=0.25Lo, W = 0.6Wo, T=0.3To %3D

5. Determine if the flexural stress of the chocolate will increase or decrease if changes are made in the chocolate's dimensions. Show solution. Initial Dimensions: Lo, To, Wo Flexural stress increase or decrease Dimension Change e.g. L = 2Lo Increase 1. W = 3W. 2. T= 0.5To 3. T= 2To, W =0.25W. 4. L=0.6Lo, W=0.3W. 5. L=0.25Lo, W = 0.6Wo, T=0.3To %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

q.p.stress
1. Determine which of the following bolt has minimum stress. A) Bolt B B) Bolt D C) Bolt A D) Bolt C 2. Determine the minimum stress, in Mpa, in the bolt. A) 5.98 B) 15.52 C) 7.76 D) 11.96 3. Determine which of the following bolt has maximum stress. A) Bolt C B) Bolt B C) Bolt A D) Bolt D 4. Determine the maximum stress, in Mpa, in the bolt. A) 45.22 B) 90.44 C) 78.14 D) 39.07 5. Determine the stress, in Mpa, in bolt D. A) 30.59 B) 61.17 C) 26.19 D) 52.38
A steel pipe of length L =7.0 ft, outside diameter d2 = 6.0 in., and inside diameter d1 = 4.5 in. is compressed by an axial force P 140 kN. The material has modulus of elasticity E = 30,000 ksi and Poisson's ratio v = 0.30. Determine the following quantities for the pipe: (a) the shortening (delta) (b) the lateral strain E' , (c) the increase Ad2 in the outer diameter and the increase Ad1 in the inner diameter, and (d) the increase At in the wall thickness.
Steel cylinder has 200 mm mean diameter with a wall 1 mm thick and 310 mm long. Determine the circumferential and longitudinal stresses that occur on the cylinder if the maximum pressure difference allowed between the inside and outside must not exceed 100 MPa. Determine the effects of three dimensional loading by determine volumetric strain and change in volume for the first steel cylinder. Modulus of elasticity E= (210 GPa), Poisson's ratio 0.30. 7
Determine stress in portion CD, BC, and in AB
A steel wire with a diameter of d = 1/16” is bent around a cylindrical drum with a radius ofR = 36”.(a) Determine the maximum normal strain in the wire.(b) What is the minimum acceptable radius of the drum if the maximum normal strain mustremain below yield? Consider an elastic modulus of 30000 ksi and yield stress of 100ksi.(c) If R = 36”, what is the maximum acceptable diameter of the wire if the maximum normalstrain must remain below yield?
When an axial load is applied to the ends of the two-segment rod shown in Figure P2.1, the total elongation between joints A and C is 7.5 mm. The segment lengths are a = 1.2 m and b = 2.8 m. In segment (2), the normal strain is measured as 2,075 um/m. Determine:(a) the elongation of segment (2).(b) the normal strain in segment (1) of the rod. (Ans. to check: Normal strain (1) = 825uE
A state of stress is specified in the figure shown below. Determine the Normal stress σy (mPa) on the Principal Plane if P1 = -5 mPa; P2 = 39 mPa and v = 21 mPa
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitude acting on horizontal and veritcal planes at the point are Sx= 12.7 ksi, Sy= 1.7 ksi, Sxy= 5.8 ksi. Assume beta= 34 degrees. Determine the normal stresses and shear stress
Determine the following: - the stress in the steel rod at C (in MPa) - The deformation of the steel rod at A. Include a negative sign if contraction (in mm., in 3 decimal places) - The stress in the steel rod at A (in MPa) - The deformation of the steel rod at C. Included negative sign if contraction (in mm, in 3 decimal places)
A cube of side 50 mm is subjected to a pressure of 80 MPa in a pressure chamber. Determine the change in the length of cube if it has a modulus of elasticity of 200 GPa and Poisson's ratio of 0.3.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. where P=25 .