Answered: 5. Determine the horizontal and…

5. Determine the horizontal and vertical components of force at C which member ABC exerts on member CEF. 4'tt B -1 ft Answers: Cx = 75 lb, Cy = 100 lb 300 Ib

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the magnitude of the projection of force F = 600 N along the u axis.

Q: Solve for the forces on members AB, AH, BC, BG, BH, GH and CG 15 N 10m RA 20 20m 20 20 SKN RAY REY

A: Consider the figure, Here, T is the tension and C is the compression.

Q: 2. The rigid bar BC weighs 50 lb/ft, is supported by the steel rod AC of cross-sectional area of…

Q: 25. 2-10. Determine the components of the 250-N force acting along thé u ànd v axes. 60° и - 70° 45°…

A: Given that:

Q: H 4.5 m 3 m E B 7 kN -12 m, 4 @ 3 m - 6 kN 4 kN Figure 1

Q: В 12 kN For the frame and loading shown, determine the components of the forces acting on member…

A: To find forces acting at B and D

Q: Find the force in the member QS of the frame shown below * 400 N 2m 2m R 2 m 45° P 2m Q

Q: In Problem D: Determine the magnitude of the force acting in member FG. Say F1 =F2 =F3 = 4 kN and…

Q: 16.Determine the moment of force P about the point O for each case CMD O a O a b RAJI P 60° P 30° q

Q: Q B 3 m C 3 m D A 3 m 2 m 3 m 3 m E F G

Q: Determine the moment of the force F about the door hinge at B. Express the result as a Cartesian…

A: The coordinated of points are,

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: As the Truss given in the question is analysed using method of joints to find the forces in each…

Q: Replace the loading on the frame by a single resultant force. Specify where its line of action…

A: Resultant Force: It is defined as the force which represents all the forces acting on a body. Unit…

Q: Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative…

A: The member forces EH and EI can be found using method of sections.

Q: Determine (approximately) the force in member BF in kips of the russ. Assuming the diagonals can…

Q: Determine the design angle θ (0° ≤ θ ≤ 90°) forstrut AB so that the 400-lb horizontal force has a…

A: Given: The angle between member AB and AC is 40o. The force in the member AC is 500 lb. Consider the…

Q: Determine the force in member CE using method of section of the truss shown if: P= 607 Kn Q= 428 Kn…

A: To find force in member CE

Q: 3. If force F =600 N, determine the components of the forces at B, C and D. %3D Draw the FBD of each…

A: Given: The value of force F is 600 N. Consider the figure,

Q: The rigid bar ABC supports a point load P at point A and is being supported by bronze bars BD & CE.…

Q: *6–76. Determine the horizontal and vertical components of force which the pins at A and Bexert on…

A: We have to determine the value of horizontal and vertical components of force which the pins at A…

Q: 1. Determine the Degree of Freedom of the following Structure 3k C. D 12n E D. 10 ft- 10 ft- 10ft 10…

A: Degree of freedom is the measure of the unknown movement that we have to address while solution that…

Q: 5.) Consider the 2D beam supported by a roller at A and a pin at B. INTERNAL FORCES f) Is the…

Q: Determine the force in members DF, DG, and EG when P = 0.9 kips and P2 = 1.8 kips.

Q: 1/52 Determine the forces in members AB, AC, and AD. 1 5 kN JORN

A: A(0,0,6)B(-1,-3,0)C(-2,0,0)D(-1,3,0)rAB=1i+3j+6krAC=-2i+6krAD=1-3j+6kF→AB=FAB[1i+3j+6k12+32+62]=[0.1…

Q: determine the smallest value of I that limits the midspan displacement to 1/360th of the span.

Q: 3) Obtain the support reactions for the beam given below. (A is pin and B is roller type support) 10…

A: Given Data: A beam subjected to Uniformly distributed load, Point load, Uniformly Varying Load and a…

Q: 3 kN 2 kN 3 30

Q: 100 N 200 N E A B 2 m 1.5 m 3 m 11.5m 1.5 m 150 N

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

A: Given :

Q: 2. The A-frame is used to support the 300-lb load applied as shown. Determine the horizontal and…

A: ∑MA=0-VF×6 + 300×10 = 0VF=500 lb ↑∑V=0VA+VF=300VA=-200 lb ↓ ∑MB=0-VE×3 + 6×300=0VE=600 lb

Q: 04) Determine the magnitude of the horizontal force F and the support reactions at pin A. If the…

A: The free-body diagram of the bar is draw below. The angle can be calculated as, θ=tan-134=36.87°

Q: y 1.5 m C 1.5 m 1 m T = 1.2 kN 3 m 2 m 1.5 m 3 m m, X.

A: A(0, 3, 0) , C( 0, 4.5 , -1.5)D(3, 0, 0) , B (0, 4.5 , 0)r→D/C = (3-0)i^+(0-4.5)j^…

Q: 3. Determine the internal normal force, shear force, and moment at point C of the beam. 60 lb/ft 690…

A: To Determine The internal normal force, shear force, and moment at point C of the beam. Please, try…

Q: Problem #4 Y KN G 30° 10 m celee B X KN 60° 60% 10 m A KN Good E 30° D 10 m Determine the force in…

Q: Determine the vertical displacement of joint C. The truss is made from A992 steel rods each having a…

A: Given :- The truss is made from A992 steel rods having diameter of 1 inch To determine :- The…

Q: Determine approximately the internal forces and the support reactions of the frames. Use the portal…

A: portal frame method: Assumption: 1. interior column is subjected with twice horizontal load than…

Q: The bar AB, which is inclined at the angle θ to the horizontal, is subjected to the four forces…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: Step 1

Q: Q1) Determine the force in member BC of the truss shown, the truss is hinged at A and supported on…

Q: 3-6.7, A vertical load of 1100 lb is supported by the three bars show in Fig. P-3-6.7. Find the…

A: Find force in each bar?

Q: Problem 4 From the given beam, the supports at B and C are rollers and fixed at A. Assuming El to be…

Q: 4. For the frame below, determine the forces acting on member AFGH. 0.5 m, 0.5 m, 0.8 m 1 m 0.25 m…

A: In physics, a solid body is a solid body where the twisting is zero or so little is ignored. The…

Q: 4-57. Determine the moment of this force F about an axis extending between A and C. Express the…

A: Position vectors of CB and AB - rCB = -2kft and rAB = 4i + 3j - 2k ft. Now, Unit vector along AC…

Q: Determine the forces in all members using method of joil 9. B 5m D 5 m A 30 kN 5 m 5 m 5 m 20 kN 5 m…

A: To find force in all members of the truss

Q: 2. Determine the forces in members EF, BF, and BC. E F 9 ft 12 fA 9 ft B

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: Determine the force in each member of the loaded truss.

Q: Four forces P = 150 N (East), Q = 200 N (North), D = 200 N (South) and S = 150 N (West) are acting…

A: Given data Forces Direction of action To find Resultant

Q: H 67.5 kN 3.6 m to D 112.5 kN E F 3.6 m B C 6 m 4.5 m- A Use cantilever method to analyze the frame.…

Q: FN N-m

A: Self-weight (SN) of the beam will be acting at the midpoint of the beam. Therefore, SN will be…

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

A: Find force in BC and CG member.

Question

5. Determine the horizontal and vertical components of force at C which member
ABC exerts on member CEF.
4 ft
B
-1 ft
4 t
Answers:
Cx = 75 lb, Cy = 100 lb
300 Ib
6 t-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
AB is made of steel and is pinned at its ends B and C. σY = 360 MPa, Est = 200 GPa. A) The effective length factor K is 1 for y-y axis and 0.5 for x-x axis, respectively. The critical load on the member AB is ___ kN. 65.7 82.8 57.1 77.1 48.5 B) The maximum load P the frame can support without buckling member AB is ___ kN. 57.8 42.8 36.4 27.8 49.2
Given P1=00K P2=19K UNKNOWN: 1. FORCE IN MEMBER GF 2. FORCE IN MEMBER FC 3. FORCE IN MEMBER CD
Determine the magnitude and type of bar forces for members BE, CF, DG and FG
For the truss in Figure 01, it is asked: choose two bars (AB, AC, AD, BC, BE, CD or CE) and determine the normal effort due to the action of load P, applied at point B, indicating the nature of the effort (whether traction or compression). To adopt:P:1100N
. A member ABCD is subjected to point loads P1, P2, P3 and P4 as shown in the Fig. Determine the force P2 necessary for equilibrium if P1 = 50 kN, P3 = 620 kN and P4 =120 kN. Determine the total elongation of the member assume E=2.1x105 MPa
5. What is the approximate moment at support a? In kN.m A. -79.86 B. -27.95 C. -73.28 D. 0 E. -10.98 F. 73.28 G. 79.86 H. 10.98 I. 27.95
Beam ABC is fixed at support A and rests(at point B) upon the midpoint of beam DE (see partaof the gure). Thus, beam ABC may be representedas a propped cantilever beam with an overhang BCand a linearly elastic support of stiffness k at point B(see part b of the figure).The distance from A to B is L =10 ft, the distancefrom B to C is L/2 = 5 ft, and the length of beamDE is L =10 ft. Both beams have the same flexuralrigidity EI. A concentrated load P =1700 lb acts atthe free end of beam ABC.Determine the reactions RA, RB, and MA for beamABC. Also, draw the shear-force and bending-momentdiagrams for beam ABC, labeling all critical ordinates.
.15 2.16 The three forces acting on the beam can be replaced with a single equivalent force R. Determine the angle θ and R. 25kN P2 60 kN P3 80 kN 40° 50° 4 m 6 Figure P2.16 COMPANY
Determine the maximum concentrated vertical load P that can act on top of the pillar of the figure. The load is applied at the centroid of the column cross section. Consider that the column is set at the top and bottom, and that the beams only act constraining the column displacement in the x-axis direction. The pillar can buckle in the two x and y directions. Use: E = 30 GPa, L = 5 m, b = 15 cm, h = 30 cm, σesc = 60 MPa
15. If Q = 1261.26 N, calculate the force in member BE in kN. Indicate whether the member is in compression (-) or tension (+).
Determine (approximately) the internal moment that member EF exerts on joint E and the internal moment that member FG exerts on joint F.