5. I copied the following out of the Arduino programming guide. Finish filling in the table showing me how toreplace the following function calls to pinMode and digitalWrite with simple C code and assembly code.Make sure you calculate the appropriate masks.PORTD maps to Arduino digital pins 0 to 7DDRD The Port D Data Direction Register - read/write (IO Address 0x0A, Memory Address 0x002A)PORTD The Port D Data Register - read/write (10 Address 0x0B, Memory Address 0x002B)(library functions) C-Code (using & and(memory mapped IO)pinMode(4,OUTPUT);masks)(legacy IO assembly)asm volatile("sbi 0x0A, 4 \n\t");//method 4, memory mapped ioasm volatile ("lds r24, 0x002A \n\t""ori r24, 0x10 \n\t"sts 0x002A, r24 \n\t"digitalWrite(4,HIGH);PORTD PORTD | 0x10digitalWrite(4,LOW);asm volatile("cbi 0x0B, 4 \n\t");//method 4, memory mapped ioasm volatile(lds r24, 0x002B \n\t""andi r24, 0xEF \n\t"*sts 0x0028, r24 \n\t";

The objective of the question is to replace the Arduino library function calls to pinMode and…

Answered: 5. I copied the following out of the…

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter6: System Integration And Performance

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Similar questions

Draw a flow chart of programmed I/O by highlighting the difference between the programmed I/O mode & Interrupt I/O.
Let's talk about each Interrupt kind. Locate the beginning, end, and in-between of the Interrupt events.
IN VERILOG If tWbus is a tri-stated output, it must be declared as _____. In a buffer register, when the LOAD control signal is disabled or inactive, what is the content of the register?" all the bits are zero all the bits are one retain the previous content high impedance What is the correct arrangement of parameters for bufif1? "(output, control, input)" "(control, output, input)" "(output, input, control)" "(input, output, control)" The keyword that represents an active low tri-state buffer is _____. A tri-state buffer is needed for all data going to the W bus. True False The keyword used for procedural blocks that are executed many times or loop continuously is
You are developping a software which should run on a specific ARM cpu. This software has around 20 000 lines of code, written in C. Most of these lines are not often executed therefore the running time of them is not an issue but you have 4 different functions (total: 80 lines of C-code, functions have 1 to 7 parameters) which take 99.9% of the running time of the software and this is a serious issue since this software is slow and its running speed needs to be improved. Since the compiler available for this specific ARM cpu is not producing an efficient code, one may suggest to write the software in assembly to be able to have a faster software.What do you think? Is it possible and how you will do it? Explain in detail and justify your answer.
Please post an ARM assembly code taking two integers from user input and passing them to a function in ARM assembly?? We have to use PUSH and POP and I don't know how.
I only have Arduino IDE and two ESP32 UWB DW1000 microcontrollers. What's an example of Arduino (C++) code for testing two ESP32 UWB DW1000 microcontrollers?
Select which of the following are stored in the interrupt vector table that is located at the bottom of memory and give the location of the appropriate ISR. INT CS AX IP
What is contained in each entry of the interrupt vector table?
Take a look at the following assembly code. Which of the following describes what is going on in the code? MOVQ $0 , %raxmystery: INCQ %rax CMPQ $5 , %rax JL mystery Group of answer choices A. This is a function call to the function 'mystery' where we increment the value stored in rax. B. This is essentially a while loop decreasing a counter by 1. C. First 0 is stored in a register--rax. Then we increment rax by 1, and compare to see if the value is 5. If it is less than 5, then we jump back to the label mystery. This is essentially a while loop incrementing a counter by 1.
// C++ code// const byte LED_PIN = 13;const byte METER_PIN = A4; void setup(){pinMode(LED_PIN, OUTPUT);pinMode(METER_PIN, INPUT); Serial.begin(9600); startTimer();} void loop(){} void startTimer(){noInterrupts(); interrupts();} ISR(TIMER1_COMPA_vect){digitalWrite(LED_PIN, digitalRead(LED_PIN) ^ 1);} 1. Based on the design and the code, explain what the primary function of this board is. Complete the code by adding appropriate comments in the designated lines. 2. Identify what the main problem in the code is and how it can affect the end-users. 3. Change the code to resolve the problem you identified in 2.
What is the main difference between interrupt-driven I/O and programmable I/O?
What is kept in each cell of the interrupt vector table?

SEE MORE QUESTIONS

Recommended textbooks for you

Systems Architecture

Computer Science

ISBN:

9781305080195

Author:

Stephen D. Burd

Publisher:

Cengage Learning

Systems Architecture

Computer Science

ISBN:

9781305080195

Author:

Stephen D. Burd

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS