If the load at E is removed, determine the force in each member of the Fink truss shown. State whether each member is in tension or compression. (Ans: FAB = 15 KN (C), FAC = 12.92 KN (T), FBC = 2.26 kN (C), FBD = 13 KN (C), FcD = 8 kN (T), FCF = 5.60 KN (T), FDF = 4 KN (T), FDE = 10 kN (C), FEF = 0 KN, FEG = 10 KN (C), FFG = 8.62 KN (T))

If the load at E is removed, determine the force in each member of the Fink truss shown. State whether each member is in tension or compression. (Ans: FAB = 15 KN (C), FAC = 12.92 KN (T), FBC = 2.26 kN (C), FBD = 13 KN (C), FcD = 8 kN (T), FCF = 5.60 KN (T), FDF = 4 KN (T), FDE = 10 kN (C), FEF = 0 KN, FEG = 10 KN (C), FFG = 8.62 KN (T))

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on the cross-section is 12 kN-m, determine the flexural stress in MPa at point A Where: tw = 22 mm; and d = 293 mm
Solve the given truss below if L = 6.4 m and F = 420 kn.
1. Find the resultant of tension F and Ta. 27.6 kNb. 37.2 kNc. 33.7 kNd. 44.6 kN2. What is the angle that their resultant makes with the horizontal rod OA? a. 28 degb. 37 degc. 33 degd. 44 deg3. Find the weight, W to prevent uplift. Use a factor of safety of 2.5. a. 49.23 kNb. 42.86 kNc. 59.51 kNd. 44.72 kN
A cantilever truss is pin-connected at joint D and is supported by a roller at G. Spacing of trusses is 3m. If the wind load is 1.44 kPa. (1) Determine the horizontal reaction at the hinged support. (2) Determine the stress of member AB. (3) Determine the stress of member BE.
The wooden members in the simple truss below have the following capacity: Shear parallel to grain = 1 MPa, Compression parallel to Grain = 11MPa, Compression perpendicular to Grain = 5 MPa 1. Find the minimum safe x. a. 73 mm b. 160 mm c. 148 mm d. 112 mm 2. Find the minimum safe y. a. 15.97 mm b. 19.45 mm c. 9.14 mm d. 18.28 mm 3. Determine the stress in member AC. a. 1.13 MPa b. 1.258 MPa c. 1.224 MPa d. 1.04 MPa
Determine the forces in members CH, AH, and CD of the loaded truss. Forces are positive if in tension and negative if in compression. Assume F1 = 1.3 kN, F2 = 3.1 kN, a = 4.0 m, b = 2.5 m, c = 1.2 m. What is the force member in: (express in kN)CH= ?AH= ?CD= ?
Take 2 KN/m in place of 1.5. Determine support reaction
For the truss shown below, applied loads are PB = 73 kN, PC = 36 kN and PD = 15 kN. Using the sign convention 'tension positive', select the correct answer for the axial force in member GH in kN: К F AR G В Рв 4@3m=12m O 1. The axial force in member GH is -60 kN. O2. The axial force in member GH is -78 kN. O 3. The axial force in member GH is -67.1 kN. Н Pc J D Ро K E 4m ?
DETERMINE ALL THE FORCES SHOW FBD
The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V to 4H. The purling are supporting a total uniform load of 15 kN/m. Properties of Channel:Sx = 119 x 10^3 mm^3Sy = 87 x 10^3 mm^3 Questions:Compute the maximum bending stress if supported by sagrods at third points.
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given structure with P = 15.5 kN. Determine the force in member CD, DG, CF, BC, EF, BF, BE, AB, AE, and FG of the truss shown. State whether each member is in tension (T)or compression (C).
Calculate the bearing reaction and internal forces of the structure if the magnitude of the concentrated load at point E is 393 kN