Answer 5 only 4. Compute the maximum force P that can be appliedby the machine operator, if the shearing stress in theasnspin at C and the axial stress in the control rod AB areealimited to 28 MPa and 35 MPa, respectively. Thechdiameters are 0.65 cm for the pin, and 1.25 cm forthe control rod. Assume single shear for the pin at B.75mm9mm-300mmB125mmCD5mmbe5. The lap joint shown is fastened by two %-in.-erdiameter rivets. Calculate the maximum safe load Pnalthat can be applied if the shearing stress in the rivetsis limited to 14 ksi and the bearing stress in the platesis limited to 18 ksi. Assume the applied load isuniformly distributed among the two rivets.4 in7/8 in7/8 in6. In the clevis shown, the bolt diameter is 25 mm andthe thickness of each yoke is 8 mm, determine theedntliemaximum amount of load P that it can carry withoutexceeding a shearing stress of 60 MPa and a bearing9=stress of 120 MPa.ESShe

(As per student demand, Solution to 5 ) To find:Calculate the maximum safe load P

5. The lap joint shown is fastened by two %-in.- diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 14 ksi and the bearing stress in the plates is limited to 18 ksi. Assume the applied load is uniformly distributed among the two rivets. 4 in 7/8 in 7/8 in

5. The lap joint shown is fastened by two %-in.- diameter rivets. Calculate the maximum safe load P that can be applied if the shearing stress in the rivets is limited to 14 ksi and the bearing stress in the plates is limited to 18 ksi. Assume the applied load is uniformly distributed among the two rivets. 4 in 7/8 in 7/8 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
31 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 2B) 4C) 14D) 0E) 6
Compute the maximum force P that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 28000 kPa and 35000 kPa, respectively. The diameters are 6.35 mm for the pin, and 12.7 mm for the control rod. Assume single shear for the pin at B.
Give me the solutions of this. Identity the maximum shear and maximum moment. Answers: Vmax = 28.98 kN, Mmax = -85.25 kN-m
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
2. What is the value of the maximum shear at C in KN?
What is the moment of the distributed load about the pin O? (a) 473 kN-m clockwise.(b) 338 kN-m clockwise.(c) 338 kN-m counterclockwise.(d) 270 kN-m counterclockwise.
calculate the Shear Force in kips at Point B (Member BC)
Draw the shear and moment diagrams for the shaft(a) in terms of the parameters shown; (b) set P = 9 kN, a = 2 m, L = 6 m. There is a thrust bearing at A and a journal bearing at B.
Find the Maximum Shear andMoment.? can you solve in 20 mins?
The shown in the figure is to be analyzed using cantilever method. Which of the following: 1. most nearly gives the axial force in member DE? A. 22.50 kN B. 37.50 kN C. 30.00 kN D. 7.50 kN 2. most nearly gives the moment at A? A. 150 kNm B. 30 kNm C. 120 kNm D. 90 kNm 3. most nearly gives the shear on member BE? A. 20.00 kN B. 10.00 kN C. 7.50 kN D. Other:_____
B. Calculate the maximum shear and moment at a point 6m from the left support. Highway uniform load = 100 kN/m; highway point load = 200 kN; uniform dead load = 30 kN/m; point dead load at midspan = 50 kN.