5. Two vertical cylindrical storage tanks are full of liquid water, density atmoshere. One is 10 m tall, 2 m diameter, the other is 2.5 m tall with diameter 4 m. What is the total force (in Newton) from the bottom of each tank to the water and what is the pressure ( in kpa)at the bottom of each tank? Note: Substitute your corresponding assigned number to the blank kg/m3, the top open to the

5. Two vertical cylindrical storage tanks are full of liquid water, density atmoshere. One is 10 m tall, 2 m diameter, the other is 2.5 m tall with diameter 4 m. What is the total force (in Newton) from the bottom of each tank to the water and what is the pressure ( in kpa)at the bottom of each tank? Note: Substitute your corresponding assigned number to the blank kg/m3, the top open to the

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.37P

See similar textbooks

Similar questions

A storage tank contains oil with specific gravity of 0.88 and depth of 20m. What is the hydrostatic pressure at the bottom of the tank in kg/cm2?
4. Assuming standard condition, what is the altitude in ft where the density is 0.001845 slug/ft3?
Question-2: in a container with a depth of 2 m, two separate liquids in two separate compartments are separated from each other through two separate doors A and B. The cap is held in balance with a rope and Mass at the end. find the weight of the mass attached to the rope. (Just find B side)
Compute the height in feet of a high building if the pressure at the ground floor is 30 in Hg and at the top of the building is 28.5 in Hg. Assume that the density of air is 0.075 lbm/ft3. PreviousNext
Find the required diameter of a droplet of water in order to have a pressure of 1 kPa within it, relative to pressure outside it. Use surface tension, a = 0.514 N/m.
According to the National Wildlife Federation, the polar bear is the largest terrestrial carnivore on Earth. Interestingly, these heavy bears spend much of their time roaming on frozen tundra and remarkably thin ice. Assume a polar bear weighs 980 pounds-force . The polar bear has a circular paw circumference of 37.7 inches . Determine the pressure the ice must be able to withstand if the polar bear is standing on its hind legs such that only two paws are in contact with the ice, in units of pounds-force per square inch .
An oil storage tank contains oil with specific gravity of 0.88 and depth of 20 meters. What is the hydrostatic pressure at the bottom of the tank in kg/cm2?
An oil of SG 0.9 is contained in a vessel. At a point the height of oil is 40 m . Find the corresponding height of water at that point.
A solid block, of specifi c gravity 0.9, fl oats such that75 percent of its volume is in water and 25 percent of itsvolume is in fl uid X , which is layered above the water.What is the specifi c gravity of fl uid X ?
A tank with vertical sides is 1.30 m square (horizontal section), 3 m high and is filled with water to a depth of 2.70 m. By how much, if at all, will be the pressure on one side of the tank be changed if a cube of wood (s=0.50) measuring 60 cm on an edge be placed in water?
A closed tank contains 0.610 m of mercury, 1.524 m of water, 2.438 m of oil of specific gravity 0.750, and an air space above the oil. If the pressure at the bottom of the tank is 276 kPa gage, what should be the reading of the gage in the top of the tank?
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 12 inches of carbon tetrachloride (SG=1.59), 4 inches of water and 2 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 9 psi. Illustrate the problem before solving. a. Determine the pressure at the interface of water and syrup. b. Determine the difference in pressure between the interface of water and syrup and the interface of carbon tetrachloride and syrup. c. Compute the hydrostatic pressure (in psi) acting at the bottom of the tank. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank. Round off ONLY the final result to three decimal places as applicable. Indicate an appropriate unit for each of your final answers.