please help me with those questions, those are from Communication Engineering, Electrical and electronics engineering. 5. What will be the final output of the following figure? where Ac = amplitudeof carrier signal, wc = frequency of the carrier signal and m(t)= messagesignal.[Ac+m(1]cos wctDC BlockerBandpass filter (+2ue)Outputcos wet6. Let, the bandwidth of the message signal is 500 Hz. What should be thevalue of we to avoid overlap in the spectra at DSB-SC modulation? Wherewc = frequency of the carricer signal.

According to the bartleby's guidelines we have to solve only one question posted by students so…

5. What will be the final output of the following figure? where Ae = amplitude of carrier signal, we = frequency of the carrier signal and m(t)= message signal. %3D (Ac+ m()Jcos wet Bandpass filter (:2ue) DC Blocker Output cos wet 6. Let, the bandwidth of the message signal is 500 Hz. What should be the value of we to avoid overlap in the spectra at DSB-SC modulation? Where

5. What will be the final output of the following figure? where Ae = amplitude of carrier signal, we = frequency of the carrier signal and m(t)= message signal. %3D (Ac+ m()Jcos wet Bandpass filter (:2ue) DC Blocker Output cos wet 6. Let, the bandwidth of the message signal is 500 Hz. What should be the value of we to avoid overlap in the spectra at DSB-SC modulation? Where

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Applying Amplitude Modulation Double Sideband Large Carrier (AM DSB-LC) results in a modulated carrier signal bandwidth approximately two times greater than the baseband signal bandwidth (fm). True False
For double sideband (DSB) signal f) What is the difficulty of synchronous demodulation (coherent detection)? g) Compare between the ordinary amplitude modulation (AM), and double sideband (DSB) modulation in terms of transmitted power, complexity of demodulation, receiver cost, and bandwidth
q16)This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. A baseband system has a signal-to-noise ratio of 23 dB and a bandwidth to bit rate ratio of 0.4 .The average bit energy to noise spectral density of this system is equal to------- a)none of the mentioned b)125 c)250 d)80
1.Select the correct statement(s) regarding frequency modulation (FM) bandwidth. a. the more the carrier frequency is allowed to change frequencies (Δf), the smaller the modulated signal bandwidth b. the larger the FM index, β, the larger the modulated signal bandwidth c. as you increase kvco, you decrease modulated signal bandwidth d. all statements are correct 2. Select the correct statement(s) regarding baseband signal modulation. a. with modulation, a baseband signal can be moved to a higher frequency thus preventing baseband signal interference b. modulation techniques are only required for analog information signals, since digital signals are represented by discrete logical values of “1” and “0” c. modulation eliminates the baseband signal’s frequency bandwidth, thus enabling greater efficiencies when transmitting a modulated carrier signal d. all statements are correct 3. A…
5. Why must modulated signals be demodulated?A. To recover the original intelligenceB. To improve the spectral efficiency of digital transmissionsC. To enable implementation of advanced featuresD. To produce one or more significant sideband pairs
- An AM signal has a carrier of 10MHz and modulating signal of 10kHz. It has a modulation index of 0.7. Write its expression an calculate power efficiency?
If the SNR value is C dB in a communication system, what can be said about the signal strength and noise power in such a system?
5. The following data is available: fc= carrier frequency = 750kHz, Ac= maximum amplitude of the unmodulated carrier = 10V fm= modulator frequency = 300Hz-8kHz modulation index m=0.5 a) What is the frequency of the upper sideband? b) What is the frequency of the lower sideband? c) What is the amplitude of the modulating signal? d) What is the maximum amplitude of the envelope of the modulated signal? e) What is the minimum amplitude of the envelope of the modulated signal? f) What is the bandwidth of the modulated wave? g) Write an expression for the modulated wave
1. Select the correct statement(s) regarding amplitude modulation (AM). a. If the AM Index is greater than 1 (i.e., µAM>1), then over modulation occurs leading to signal distortion b. With AM, the message is captured as amplitude changes to the carrier’s amplitude. c. The AM modulated carrier bandwidth is dependent upon the baseband signal’s frequency bandwidth d. All of the above are correct 2. What is true about the frequency bandwidth of a modulated electrical or electromagnetic (EM) signal? a. signal bandwidth is only determined by the frequency of the unmodulated carrier wave b. modulation technique and the amount of information transmitted determines the signal’s bandwidth c. only the baseband signal determines frequency bandwidth; i.e., modulation technique has no impact on bandwidth d. a and c are true 3.Regarding carrier modulation, identify the carrier signal variable(s)…
Prove that narrowband FM offers no improvement in SNR over AM?
A. The baseband signal in the image Is transmuted by using a linear delta modulation (ΔM), the modulator has the following specifications Sampling rate = 5 Fnyquist, where Fnyquist is the Nyquist rate of the baseband signal, bandwidth = 5 KHz. 1. Determine the maximum step size Δ for delta modulation of this signal, which required avoiding slope overload. 2. Determine the signal to noise ratio in decibel for the signal. 3. What is the maximum power that be transmitted without slope overload distortion 4. if the step size of the delta modulation is 0.02 determine the amplitude and maximum power of baseband signal to a void slope overload .
For double sideband (DSB) signala) Write the time domain equation XDSB(t).b) Write the frequency domain equation XDSB(ω).c) Draw the block diagram for DSB signal Generation.d) Draw the receiver block diagram. e) Explain with drawing the demodulation process of double sideband (DSB) signal using coherent detector.f) What is the difficulty of synchronous demodulation (coherent detection)? g) Compare between the ordinary amplitude modulation (AM), and double sideband (DSB) modulation in terms of transmitted power, complexity of demodulation, receiver cost, and bandwidth