5.11 Two perfectly conducting cylindrical surfaces are located at p = 3 and p = 5 cm. The total current passing radially outward through the med- ium between the cylinders is 3 A dc. (a) Find the voltage and resistance between the cylinders, and E in the region between the cylinders, if a conducting material having o = 0.05 S/m is present for 3 < p < 5cm. (b) Show that integrating the power dissipated per unit volume over the volume gives the total dissipated power.

5.11 Two perfectly conducting cylindrical surfaces are located at p = 3 and p = 5 cm. The total current passing radially outward through the med- ium between the cylinders is 3 A dc. (a) Find the voltage and resistance between the cylinders, and E in the region between the cylinders, if a conducting material having o = 0.05 S/m is present for 3 < p < 5cm. (b) Show that integrating the power dissipated per unit volume over the volume gives the total dissipated power.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Inductance. Consider the configuration of a wire with 90° bends as shown below. A small loop, with its sides of length a and width d = a/16 is placed with its plane lying along xz principal plane as shown. Stating all assumptions, determine mutual inductance between the loop and the wire. a/2 9/2 2a
2) Vo voltage is applied to the metal parallel plate capacitor system given in the figure. The region between the plates is filled with dielectric material of &-2.4. Bottom plate grounded and d-2mm in the z-axis of the top plate when placed at z=0 are within distance. For tension in the interplate region boundary conditions: If V(z)-0 volts for z-0 and V(z)-Vo volts for z-d; a) Potential expression in the interplate region V=? b) Electric field strength E-? c) Electric flux density D-? d) Surface charge densities of the plates p.=?
Q14. An air filled parallel plate capacitor is arranged such that the upper plate carries surface charge density 2C/m² and lower plate carries surface charge density -2C/m² as shown in figure. The electric field intensity under the bottom plate will be
A cylindrical long solenoid of length 2000 mm has 20 mm diameter. If number of turns wounded on solenoid is 2000 turns what is value of inductance.
A hollow conductor us at a potential V. The potential at any point inside the hollow is,
Determine the mutual inductance between a very long straightwire and a conducting circular loop of radius “b” m set up “d” mapart on the same plane as shown figure.Problem:
Question A capacitor with parallel plates, of area A and separation 2a, is connected to a potential difference AV. Then a conductive metal plate of area is introduced A/2 and thickness a up to the middle of the capacitor (red in the figure). Finally it is introduced an insulating material of dielectric constant k in the second half (blue in the figure), with equal area and thickness as conductive material. Find The capacity and energy accumulated when the capacitor is with the conductor. What do you mean by c3 and c2? Are the capacitor with conductor and the other with air? What area and distance is used to calculate the capacitor with air and to calculate the one with the conductor?
> Figure 1 shows a ferromagnetic core whose mean path length is 40 cm. There is a small gap of 0.05 cm in the structure of the otherwise whole core. The cross-sectional area of the core is 12cm?, the relative permeability of the core is 4000 and the coil of wire on the core has 400 turns. Assume that fringing in the air gap increases the effective cross-sectional area of the air gap by 5 percent. Given this information. Find the total reluctance of the flux path (iron plus air gap) and the current required to produce a flux density of 0.5 T in the air gap. N=400 0.05 cm A-12 cm - 40 cm Figure 1
6- Why an insulator is represented as a capacitor C? What are the assumption modes?
A Suppose a copper conductor of length (UUm and cross-sectional area (A)m" and resistivity (6)N m, its resistance is [R = p(1/A)]. This copper conductor wounded around a ferromagnetic core, forming (N) turns. When this coil fed by a DC voltage (Va), its steady state current will be [lae = (Vac/R)]. But when this coil fed by an ms value of an AC voltage (Vms = Vdc), a steady state AC current of an rms value (lac) will pass through it. Explain the following questions: a) Why (lac < ldc) in this case, in spite of (Vms = Va)? What happens inside the electric circuit leads to reduce the current? b) What is the current waveform in this case? c) What is the voltage waveform across the coil? d) What is the type of the ammeter used in this circuit? e) Assume that the core length (le), cross sectional area (Ac), and its hysteresis loop data are known, what is its self inductance (L)? f) is the self inductance of this coil been constant? Or not? Why? g) If it is not constant, then what is it…
> Figure 1 shows a ferromagnetic core whose mean path length is 40 cm. There is a small gap of 0.05 cm in the structure of the otherwise whole core. The cross-sectional area of the core is 12cm2, the relative permeability of the core is 4000 and the coil of wire on the core has 400 turns. Assume that fringing in the air gap increases the effective cross-sectional area of the air gap by 5 percent. Given this information. Find the total reluctance of the flux path (iron plus air gap) and the current required to produce a flux density of 0.5 T in the air gap. N=400 tums 0.05 cm A=12 cm? le-40 cm Figure 1
An infinitely long straight wire carries 1000 A of current and in the vicinity, there is a circular conducting loop of 100 mm diameter with the center of the loop 1m away from the straight conductor. Both the wire and the loop are coplanar. The magnitude and direction of current in the loop that produces a zero flux density at its center is?