5.13 (B). A 500mm x 175 mm steel beam of length 8 m is supported at the left-hand end and at a point 1.6 m from the right-hand end. The beam carries a uniformly distributed load of 12 kN/m on its whole length, an additional uniformly distributed load of 18 kN/m on the length between the supports and a point load of 30kN at the right- hand end. Determine the slope and deflection of the beam at the section midway between the supports and also at the right-hand end. El for the beam is 1.5 x 10® Nm2. [U.L.][1.13 x 10-4, 3.29 mm, 9.7 x 10-, 1.71 mm.]

5.13 (B). A 500mm x 175 mm steel beam of length 8 m is supported at the left-hand end and at a point 1.6 m from the right-hand end. The beam carries a uniformly distributed load of 12 kN/m on its whole length, an additional uniformly distributed load of 18 kN/m on the length between the supports and a point load of 30kN at the right- hand end. Determine the slope and deflection of the beam at the section midway between the supports and also at the right-hand end. El for the beam is 1.5 x 10® Nm2. [U.L.][1.13 x 10-4, 3.29 mm, 9.7 x 10-, 1.71 mm.]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 5-meter cantilever beam 300 mm x 400 mm in cross-section carries a total uniformly distributed load of 26 kN/m. E=25GPA. What force (kN) should be applied at the mid-length of the beam in order to balance its deflection at the free end.
A 12-meter simple beam is loaded with 3 concentrated loads P at the middle-quarters. If P = 20 kN and EI is constant. Calculate the slope at 2 meters from the left support.
A 10 m cantilever beam has a uniform load of 2.5 KN/m from left to right end. Find the maximum deflection of the beam. (El = 11,000 KN.m2) .
For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
The beam supports the roof made from asphalt shingles and wood sheathing boards. If the boards have thickness of 38 mm and a specific weight of 7.86 kN/m3, and the roof’s angle of slope is 30O, determine the dead load of the roofing per square meter that is supported in the x and y directions by the purlins.
A cantilever beam, 6m long, fixed at point A and free at point B, is subjected to a downward uniform load 50 kN/m throughout the beam. a. Determine the slope of A wrt B. b. Determine the slope of B wrt A.
From the given beam in the figure, using a uniform live load of 17 kN/m and a concentrated live load of 86 kN. Compute the maximum negative shear (kN, include sign) at C by influence lines. Use a = 4 m., b = 1 m., and c = 5 m. ROUND OFF TO TWO DECIMAL PLACES.
A steel framework is used to support the 4" reinforced concrete slab that carries a uniform live loading of 1.9kPa. Sketch the loading that acts along members BE and FED. b = 3 m and a = 2.5 m.
A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees.
From the given beam in the figure, using a uniform live load of 16 kN/m and a concentrated live load of 91 kN. Compute the maximum negative shear (kN, include sign) at C by influence lines. Use a = 3 m., b = 1 m., and c = 5 m.
The inverted T section of 6 m overhang bearn has the properties shown. The beam carries a uniformly distributed load W_{0} over its entire length and a concentrated load of 5 KN, 3 m from the rightmost support. Determine W_{0} if f b(T) =30 MPa and f b(C) =70 MPa
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)