32 pdf213100% +6-51. The assembly is made from a steel hemisphere,Pa = 7.80 Mg/m,2.70 Mg/m. Determine the height h of the cylinderand%3Danaluminumcylinder,Pat=so that the center of gravity of the assembly is located atM= 160 mm.80 mm160 mm89F Sunny

Name: 32 pdf213100% +6-51. The assembly is made from a steel hemisphere,Pa
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 32 pdf213100% +6-51. The assembly is made from a steel hemisphere,Pa = 7.80 Mg/m,2.70 Mg/m. Determine the height h of the cylinderand%3Danaluminumcylinder,Pat=so that the center of gravity of the assembly is located atM= 160 mm.80 mm160 mm89F Sunny

Centre of mass of composite body zbody = ∑mizi∑mimi = mass of elementZi= height of centre of mass…

Answered: 6-51. Pa = 7.80 Mg/m 2.70 Mg/m.…

Engineering

Mechanical Engineering

6-51. Pa = 7.80 Mg/m 2.70 Mg/m. Determin %3D Pal= so that the center of gravity of the as Z= 160 mm.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.40P: By integration, find the centroid of the surface of the hemisphere. Compare your result With Table...

See similar textbooks

Similar questions

Both the top of the tank and the end of the slanted tube are open to the atmosphere. If L = 3.65 m., x = 98 cm., y = 94 cm., SG1 = 0.98, SG2 = 1.88, what is the angle of tilt (in degrees) of the tube? Accepted answer ranges from 22.42-24.422. Show solution.
A 27 m vertical column of fluid (density 1878 kg.m3) is located where g= 9.65 m/sec2. Find the pressure at the base of the column.Ans. 489.313 kPa Please give me the solution.
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness. Seefigure 103.
Determine the centroid of the surface shown in the figure below in two ways: The. Using a vertical differential element of dx thickness; B. By double integration The chart should contain all the information necessary to understand the issue
Determine the distance (h) in mm ,that a column of mercury in the tube will be depressed when the tube is inserted into the mercury at a room temperature of 20°C. Set ( D= 6 ) mm , density of mercury =13550 Kg/m3 , (s) surface tension 37.5x10-2 N/m , a= 57 o 2- The Value of (h) is equal to .....?
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness.
Determine the distance (h) in mm ,that a column of mercury in the tube will be depressed when the tube is inserted into the mercury at a room temperature of 20°C. Set ( D= 12 ) mm , density of mercury =13550 Kg/m3 , (s) surface tension 37.5x10-2 N/m , a= 42 o The Value of theata is equal to ? The Value of (h) is equal to?
A spherical buoy has a diameter of 1m and floats half submerged in sea water. Determine the mass of the buoy. A piece of material density 5670 kg/m3 is now suspended beneath the buoy causing it to be just submerged. Determine the mass of material used. Ans: mass of buoy: 268.3kg, mass of materlal: 327.5
A cylindrical pressure vessel has an inner diameter of 1.2 m and a thickness of 12mm. Determine the maximum internal pressure it can sustain so that neither itscircumferential nor its longitudinal stress component exceeds 140 MPa. Under thesame conditions, what is the maximum internal pressure that a spherical vessel with a similar inner diameter can sustain?
-4°C ice weighing 300 g was placed on a glass that has a diameter of 6 cm. Determine the depth of the melted ice. Assume ambient temperature of 27°C. ANSWER: 10.61 cm
A spherical gas tank has an inner radius of r = 1.5m, if it subjected to an internalpressure of p = 300kPa, determine its minimum thickness if the maximum normalstress is not to exceed 12MPa Note: indicate free body diagram.
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.