6 Ydu will obtain 2.0 L of tap water for you water hardness test. The water hardness test uses a precipitation reaction to precipitate the Calcium bicarbonate present out of solution by adding 1.9 g of Ca(OH) represented by the following equation: Ca(HC03|21ag) + Ca(OH)215) > 2CaCOsisi + 2 H20 ml What is the percent yield of CaCO3 produced in the hard water test? (fig. 4)

6 Ydu will obtain 2.0 L of tap water for you water hardness test. The water hardness test uses a precipitation reaction to precipitate the Calcium bicarbonate present out of solution by adding 1.9 g of Ca(OH) represented by the following equation: Ca(HC03|21ag) + Ca(OH)215) > 2CaCOsisi + 2 H20 ml What is the percent yield of CaCO3 produced in the hard water test? (fig. 4)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter10: Oxidation, Degradation, Corrosion, Electroprocessing, Batteries, And Fuel Cells

Section: Chapter Questions

Problem 10.1P

See similar textbooks

Similar questions

Describe the lime soda process for removing the hardness of water. Calculate the amountof lime and soda required for treatment of 10,000 liters of water containing the followingsalts in ppm.Al2(SO4)3 = 34.2 HCl = 7.3MgCl2= 19.0 NaCl= 58.5
A tank contains 200 liters of fluid in wich 30 grams of salt in dissolved. Brine containing 1 gram of per liter is then pumped into the tank at a rate of 4 liter/minutes the well mixed solution is pumped out at the same rate. Find the number A(t) of grams of salt in the tank at time t.
Note: Read the question carefully and give me right solution according to the question. I want clear solution with clear steps. A water contains 38.50 mg/L as CaCO3 of carbon dioxide, 288.00 mg/L as CaCO3 of Ca2+ and 53.00 mg/L as CaCO3 of Mg2+. All of the hardness is carbonate hardness. Using the stoichiometry of the lime soda ash softening equations, what is the daily sludge production (in dry weight, kg/day) if the plant treats water at a rate of 56.00 MGD? Assume that the effluent water contains no carbon dioxide, 30.0 mg/L as CaCO3 of Ca2+ and 10.0 mg/L as CaCO3 of Mg2+. Be sure to calculate the mass of CaCO3 and Mg(OH)2 sludge produced each day.
The water hardness in an area is reported as 700 ppm total dissolved solids. This is the same concentration as O 0.07% O 0.7% 07% O 0.007%
Glycerin (specific gravity 1.26) in a processing plant flows in a pipe at a rate of 805 L/s. At a point where the pipe diameter is 765 mm, the pressure is 300 kPa. Find the pressure at a second point where the pipe diameter is 300 mm if the second point is 1.0 m lower than the first point, neglect the head loss
The pOH of a basic solution is 3.33. What is pH?
10-kg of R-134a fill a 1.348-m3 rigid container at an initial temperature of 240oC. The container is then heated until the pressure is 200 kPa. Determine the final temperature and the initial pressure
A tank originally contains 380 liters of brineholding 450 g of dissolved salt. 8 liters/min ofbrine containing 3.75 g/L of salt enters the tankand the mixture assumed uniform leaves therate of 12 L/min. Determine the amount of saltafter 10 min.
In the tank of 100 liters of brine containing 50kg totally dissolved salt. Pure water is allowed to run into the tank at the rate of 3 liters per minute. Brine runs out of the tank at rate of 2 liters minute. The instantaneous concentration in the
6 cans containing soda made out of aluminum ( E = 69 GPa, σY = 240 MPa ) material are shaken. Shaking them creates an internal pressure of 0.14 MPa in each can. A uniform load of W is applied to the cans through a plate which has a negligible weight. The inner diameter of each can is 2R = 62 mm, the wall thickness is t = 0.25 mm and the length is L = 112 mm. According to the von - Mises yield criterion, determine the maximum magnitude of the applied load W. Note: The weight of the cans will be neglected in calculations. Accept that the liquid in the cans does not provide any support to the cans and no buckling occurs in the cans.
Calculate the followingi. Liquid limitii. Plastic limitiii. Plasticity index
You need to soften water at a 20 MGD potable water treatment facility using lime (Ca(OH)2) and soda ash (Na2CO3). Chemical analysis of the water revealed the constituent concentrations in the table below. Concentration Molecular Weight CO2 6 mg/L 44 g/mol Ca2+ 20 mg/L 40 g/mol Mg2+ 10 mg/L 24.4 g/mol Na+ 5 mg/L 23 g/mol Alkalinity 105 mg/L 100 g/mol SO42- 4 mg/L 96 g/mol Cl- 7 mg/L 35.5 g/mol What is the Carbonate Harness (concentration) in this system? Calculate the quantity of softening materials required on a daily basis for and excess lime treatment process (assume 24 hr operation).