6. A closed cylindrical tank that is 8 ft in diameter and 24 ft long is completely filled with gasoline. The tank, with its long axis horizontal, is pulled by a truck along a horizontal surface. Determine the pressure difference between the ends (along the long axis of the tank) when the truck undergoes an acceleration of 5 ft/s.

6. A closed cylindrical tank that is 8 ft in diameter and 24 ft long is completely filled with gasoline. The tank, with its long axis horizontal, is pulled by a truck along a horizontal surface. Determine the pressure difference between the ends (along the long axis of the tank) when the truck undergoes an acceleration of 5 ft/s.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
an inclined rectangular gate with water on one side. determine the total resultant force acting on the gate and the location of the center of pressure
A glass-walled fish tank is 2 ft wide by 6 ft long by 3ft deep. When the water (y = 62.4 lb /ft^3) in the tank is 2.5 ft deep, determine the magnitude of the resultant force R exerted on a 2- by 3-ft end plate by the water pressure and the distance from the water surface to the center of pressure.
A closed tank rectangular in plane with vertical sides is 1.8m deep and contains water to a depth of 1.2m. Air is pumped into the space above the water until the air pressure is 35kN/m2. If the length of one wall of the tank is 3m, determine the resultant force on this wall and the height of the centre of pressure above the base
Q4:-Locate the vertical axis of rotation and the speed of rotation (r/s) of the U-tube of fig.(4),as that the pressure of liquid at points A and B at (zero gauge)
A water tank, open at the top, consists of a right circular cylinder and a right circular cone, as shown. If the altitude of the cylinder is three times its radius, and the altitude of the cone is two times the same radius, find the altitude of the cylinder (1 gal=231 cu. in.).
An open cylindrical tank has a base diameter of 1.2 meter and contains 3.86 meter deep water. the tank is rotated about its vertical axis at 80 rpma. What is the maximum height of the tank so that no water will spill at 80 rpm? b. If ω = 140 MPa, what will be the pressure at the center bottom of the tank?
Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is 100 kPa, determine the distance between the two fluid levels of the manometer if the fluid is
A tiny steel cube is suspended in water by a string. If the lengths of the sides of the cube are very small, how would you compare the magnitudes of the pressures on the top, bottom, and side surfaces of the cube?
A 1-kg cube of wood floats in an upright position in fresh water. If a side of the cube measures 12.5 cm, determine the pressure acting at the bottom of the cube due to the water. How deep is the cube floating?
Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm. If the intervening passages are filled with oil and a force of PB=4.6kn is acting on B. What must be the pressure in N/m2 exerted at A?
A large vertical dam in the shape of a symmetric trapezoid has a height of 30 m, a width of 20 m at its base, and a width of 40 m at the top (as shown). What is the total force on the face of the dam when the reservoir is full?